manualshive.com logo in svg

Edge-Core ECS4120-28F, Reference Manual, Page: 580 / 938

Share
Download
Edge-Core ECS4120-28F Reference Manual Download Page 580

Chapter 21

  |  VLAN Commands

Configuring L2PT Tunneling

–  580  –

Configuring L2PT Tunneling

This section describes the commands used to configure Layer 2 Protocol Tunneling 
(L2PT).

l2protocol-tunnel

tunnel-dmac

This command configures the destination address for Layer 2 Protocol Tunneling 
(L2PT). Use the 

no

 form to restore the default setting.

Syntax 

l2protocol-tunnel tunnel-dmac

 

mac-address

mac-address

 – The switch rewrites the destination MAC address in all 

upstream L2PT protocol packets (i.e, STP BPDUs) to this value, and forwards 
them on to uplink ports. The MAC address must be specified in the format 
xx-xx-xx-xx-xx-xx or xxxxxxxxxxxx.

Default Setting 

01-12-CF-.00-00-02, proprietary tunnel address

Command Mode 

Global Configuration

Command Usage 

◆

When L2PT is not used, protocol packets (such as STP) are flooded to 802.1Q 
access ports on the same edge switch, but filtered from 802.1Q tunnel ports. 
This creates disconnected protocol domains in the customer’s network.

◆

L2PT can be used to pass various types of protocol packets belonging to the 
same customer transparently across a service provider’s network. In this way, 
normally segregated network segments can be configured to function inside a 
common protocol domain.

◆

L2PT encapsulates protocol packets entering ingress ports on the service 
provider’s edge switch, replacing the destination MAC address with a 
proprietary MAC address (for example, the spanning tree protocol uses 10-12-
CF-00-00-02), a reserved address for other specified protocol types (as defined 
in IEEE 802.1ad – Provider Bridges), or a user-defined address. All intermediate 
switches carrying this traffic across the service provider’s network treat these 

Table 112:  L2 Protocol Tunnel Commands 

Command

Function

Mode

l2protocol-tunnel tunnel-
dmac

Configures the destination address for Layer 2 Protocol 
Tunneling

GC

switchport 
l2protocol-tunnel

Enables Layer 2 Protocol Tunneling for the specified 
protocol

IC

show l2protocol-tunnel

Shows settings for Layer 2 Protocol Tunneling

PE

Summary of Contents for ECS4120-28F











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments