manualshive.com logo in svg

Edge-Core ECS4120-28F, Reference Manual, Page: 321 / 938

Share
Download
Edge-Core ECS4120-28F Reference Manual Download Page 321

Chapter 9

  |  General Security Measures

DHCPv6 Snooping

–  321  –

DHCPv6 Snooping

DHCPv6 snooping allows a switch to protect a network from rogue DHCPv6 servers 
or other devices which send port-related information to a DHCPv6 server. This 
information can be useful in tracking an IP address back to a physical port. This 
section describes commands used to configure DHCPv6 snooping. 

ipv6 dhcp snooping

This command enables DHCPv6 snooping globally. Use the 

no

 form to restore the 

default setting.

Syntax 

[

no

]

 ipv6 dhcp snooping

Default Setting 

Disabled

Command Mode

Global Configuration

Command Usage 

◆

Network traffic may be disrupted when malicious DHCPv6 messages are 
received from an outside source. DHCPv6 snooping is used to filter DHCPv6 
messages received on an unsecure interface from outside the network or fire 

Table 61: DHCP Snooping Commands  

Command

Function

Mode

ipv6 dhcp snooping

 

Enables DHCPv6 snooping globally

GC

ipv6 dhcp snooping option 
remote-id

Enables insertion of DHCPv6 Option 37 relay agent 
remote-id

GC

ipv6 dhcp snooping option 
remote-id policy

Sets the information option policy for DHCPv6 client 
packets that include Option 37 information

GC

ipv6 dhcp snooping vlan

 

Enables DHCPv6 snooping on the specified VLAN

GC

ipv6 dhcp snooping 
max-binding

Sets the maximum number of entries which can be 
stored in the binding database for an interface

IC

ipv6 dhcp snooping trust

 

Configures the specified interface as trusted

IC

clear ipv6 dhcp snooping 
binding

Clears DHCPv6 snooping binding table entries from RAM PE

clear ipv6 dhcp snooping 
statistics

Clears statistical counters for DHCPv6 snooping client, 
server and relay packets

PE

show ipv6 dhcp snooping

 

Shows the DHCPv6 snooping configuration settings 

PE

show ipv6 dhcp snooping 
binding

 

Shows the DHCPv6 snooping binding table entries

PE

show ipv6 dhcp snooping 
statistics

Shows statistics for DHCPv6 snooping client, server and 
relay packets

PE

Summary of Contents for ECS4120-28F











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments