background image

Check Box for These Contents 

In the event of missing or defective parts please call our customer service 
dept. at 

1 800 282 9346, ext #20

 

(Mon. to Fri. 8:00 AM to 4:00 PM EST)

.

    1.  

Keystone Lid

 (1)

 

    2. 

 Keystone Insert 

(1)

    3. 

 Keystone Body 

(1)

 

    4. 

 Keystone Bottom Plate 

(1)

 

    5. 

 Arch Spindle - Long 

(2)

    6. 

 Arch Spindle - Short 

(2)

    7. 

 Arches 

(2)

    8. 

 Post Caps 

(2)

 

    9. 

 Top Rail 

(1)

 10. 

 Posts 

(2)

 11. 

 Vertical Spindles 

(7)

 12. 

 Horizontal Spindles 

(3)

 13. 

 Bottom Rail 

(1)

 14. 

 Ground Stakes 

(2)

 15. 

 1 1/2” Self-Auguring Stainless Steel Screw 

(20)

    

Tools You Will Need

    •  Cordless Drill
    •  Hammer 
    •  Tape Measure
    •  Level 
    •  Shovel 

General Information

    • 

 Read Instructions through carefully before beginning assembly.

    •  When assembling components, place on a non-abrasive surface 

(i.e. shipping box) 

to avoid scratching. 

    •  We recommend an area approx 5’x 8’ for unobstructed assembling.
    •  You should not need to use excessive force when assembling component.

The Vienna Trellis

Please read through before starting assembly.

A S S E M B LY   I N S T R U C T I O N S

1

www.edenarbors.com 

1

2

15

Not to Scale

6

3

4

5

IMPORTANT:  CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.

Ver 1/Aug 2011

14

83.75 in

49 in

42 in

6 in

49 in

2 in

7

8

9

10

11

12

13

Summary of Contents for The Vienna Trellis






Reviews: