Eden Solo CXC-300 Owner'S Manual Download Page 6

 

OTHER CONSIDERATIONS

 

 
Suggested Speaker Systems 

– Your 

speaker system, should be chosen to 
accommodate the characteristics of your 
amplifier and your predominant application.  
If you will only be using one cabinet. It will 
be at 8 Ohms as are all the CXC models.  
 
If you are using two cabinets, they should 
both be 8 Ohm models so their combined 
impedance will be 4 ohms.  
 

Headphone Jack as Line Driver

 – On 

some occasions (such as high-volume or 
outdoor situations) it may be desirable to 
use the CXC-300/400 along with an 
additional power amplifier and added 
cabinets.  A standard shielded instrument 
cable may be used to connect from the 
headphone jack of the CXC-300/400 to an 
unbalanced input of a standard power 
amplifier.  This will provided a signal that is 
post EQ and master volume controls, 
allowing the entire system to be controlled 
from the CXC Amplifier.   
 

Using the CXC-300/400 With out 
Speakers 

  

This amplifier is designed to be used safely 
with headphones only, without the loud 
speaker plugged in. No harm will result from 
using the amplifier in this fashion.  This 
allows the use of the unit for practice with 
headphones and as a preamplifier with other 
amplifiers. 
 

MAINTENANCE 

 
Your Eden amplifier has been designed to 
require minimal routine maintenance.  
Attention to the following areas will ensure 
optimum performance of your amplifier. 
 

Contact Point Cleaning – 

One of the 

weakest links in most bass amplification 
systems are the solderless connection 
points where instruments, speaker cabinets, 
effects, and other devices are connected to 
the amplifier.  (The most vulnerable of these 
types of connection is the jack on your 
instrument).  In addition to contamination 
from airborne pollutants, these points are 

frequently assaulted by connectors that 
have picked up debris from dirty stages, 
cases, etc.  These points should be cleaned 
regularly with a cotton swab soaked in 
denatured alcohol or a commercially 
available de-oxidant.  Frequent cleaning of 
the plugs on your cords is also 
recommended. 
 

Dust Removal – 

You should periodically 

inspect the ventilation openings on the  and 
sides of the unit to ensure that they have not 
become blocked by accumulated dust.  
Vacuum the openings to remove any dust 
buildup. 
 

Tube Replacement

 –This system does 

not use tubes. The CXC amplifiers 
feature a discrete  FET front end 
coupled to Bi-FET OP Amplifiers for the 
preamplifier section.  

 

Service – 

In the event of amplifier 

malfunction, or questions about your unit’s 
operating features, you should contact the 
your Dealer, the factory, or one of our 
authorized service centers for assistance. 
 
 

Eden Electronics 

P.O. Box 338 

115 second Street 

Montrose, Minnesota   

55363 

 

(763) 675-1890 

 

(763) 675-3777(fax) 

 

eden@eden-electronics.com

 

 

http://www.eden-

electronics.com 

Summary of Contents for Solo CXC-300








Reviews: