©2012 Edelbrock LLC
Catalog #60037, 60039, 300649
Page 2 of 4
Brochure #63-60039
Rev. 3/12- QT
ACCESSORIES
Although Edelbrock Performer RPM Buick cylinder heads will accept most OEM components (valve covers, intake manifold, head bolts, etc.), we highly
recommend that premium quality hardware be used with your new heads.
•
Head Bolts or Studs:
High quality head studs or head bolts with
hardened washers must be used to prevent galling of the aluminum
bolt bosses. We recommend Edelbrock Head Bolt Kit #8503. Bolt
threads, underside of bolt heads, and washers should be lubricated
prior to installation and torquing, we recommend using Torco Engine
Assembly Lube #1075. Use thread sealant on any bolts that go into
coolant passages.
•
Rocker Arms:
Requires adjustable 1.6:1 ratio. Cylinder heads
accept commonly available 3/8” stud-mounted, small-block
Chevrolet rocker arms.
The valve springs supplied will
accommodate valve lifts up to .600”. Always check rocker-to-valve
spring and rocker to valve cover clearance before final assembly.
•
Intake Manifold:
Although stock intake manifolds may be used,
we highly recommend the use of Edelbrock Performer Buick or B4B
intake manifolds. Intake ports are CNC-profiled to match Edelbrock
#7246 intake gaskets which are recommended for this application.
•
Exhaust Headers:
Most headers or exhaust manifolds designed
for original equipment heads will fit the Edelbrock Performer RPM
Buick Cylinder Heads. Exhaust ports are CNC-profiled to match
Edelbrock #7247 exhaust gaskets which are recommended for this
application.
•
Valve Covers:
Use any OEM steel, or aftermarket aluminum valve
covers designed to fit stock cylinder heads. When using roller
rockers, the stock valve covers may need to be spaced upwards
with extra thick valve cover gaskets, or by laminating multiple
gaskets together using silicone sealer or gasket adhesive.
•
Spark Plugs:
Use 14mm x 3/4” reach gasketed spark plugs with
a 5/8” hex. Heat range will vary by application; typical street plug
would be Champion RC12-YC.
Use anti-seize compound on the
plug threads to prevent galling in the cylinder head, and torque
to the spark plug manufacturers specification for aluminum
heads.
•
Lubricants:
For added performance and protection, we recommend
using Edelbrock performance lubricants.
IMPORTANT NOTES: READ BEFORE BEGINNING INSTALLATION!
For a successful installation, the Edelbrock Performer RPM Cylinder
Heads require some components other than original equipment parts. To
complete your installation, you will need the following items:
❑
Head gaskets; Edelbrock #7346
❑
Intake manifold gaskets; Edelbrock #7246
❑
Exhaust gaskets; Edelbrock #7247
❑
Valve cover gaskets; Edelbrock #7546
NOTE:
Edelbrock Cylinder Head Gasket Set #7369 may
also be used in place of individual gaskets. This set
contains all gaskets necessary for cylinder head
installation, including cylinder head, intake, exhaust, and
valve cover gaskets.
❑
Edelbrock head bolt kit #8503 (see instructions below)
❑
14mm x 3/4” reach x 5/8” hex, gasketed spark plugs (heat
range to be determined by specific application)
❑
Adjustable rocker arm assembly. Cylinder head is designed to
use most commonly available Stud Mounted small block
Chevrolet adjustable rocker arms. Always check rocker-to-
valve spring and rocker to valve cover clearance before final
assembly. Valve cover modification may be required with the
use of roller rockers (See
Valve Covers section below).
❑
Pushrods compatible with adjustable rocker arm assembly. We
used Pioneer #815211 in our testing (Length: 9.650”).
CHECKING VALVE-TO-PISTON CLEARANCE:
Prior to installation, it is
highly recommended that valve-to-piston clearances are checked and
corrected to minimum specs, if necessary.
Minimum intake valve
clearance should be .080”. Minimum exhaust valve clearance should be
.110”. The point of minimum intake valve to piston clearance will usually
occur somewhere between 5° and 20° After Top Dead Center during
valve overlap. The point of minimum exhaust valve to piston clearance
will usually occur 20° to 5° Before Top Dead Center during valve overlap.
Performer RPM Buick heads should be compatible with stock pistons in
engines that have the stock or recommended camshafts. Other than
recommended camshafts may require aftermarket pistons and/or
custom machining of your pistons.
ROCKER GEOMETRY:
Rocker geometry should be checked, making
sure that the contact point of the roller (or pad on a stock type rocker
arm) remains properly on the valve tip and does not roll off the edge.
Visual inspection of the rockers, valve springs, retainers, and pushrods
should be made to ensure that none of these components come into
improper contact with each other. If problems with valve train geometry
occur, changes such as pushrod length may have to be made.
BEFORE BEGINNING INSTALLATION (CONTINUED)
High Performance Break-In Oil
SAE 30
P/N 1070
Engine Assembly Lube
-
P/N 1075
Zinc Additive
-
P/N 1074
High Performance Synthetic
10w40 w/Zinc
P/N 1072
High Performance Synthetic
5w30 CAT Safe
P/N 1071
High Performance Petroleum
10w40 w/Zinc
P/N 1073
Engine Oils
Or supplement your favorite brand of engine oil
Protect your brand new engine
