Edelbrock E-Force 1580 Installation Instructions Manual Download Page 28

©2011 Edelbrock LLC
Part #1580 & 1585

Brochure #63-1580

Rev. 1/11 - AJ/mc

Edelbrock 4.6L Ford Supercharger System

for 2005 and later Mustang GTs

Installation Instructions

Page 28

153. Lower the driver side coil cover into place, orienting
the bracket so that it lines up with the bolt provision
below the TMAP sensor. Use caution not to pinch the
TMAP wire harness as you are fastening the cover bracket
to the runner with the supplied thumb screws. Verify that
the cover stands are flush on the valve cover and not
pinching any wires or hoses. Install the oil dipstick.

154. Install the passenger side cover by lowering it into
place and fastening the thumbscrews. Use caution not to
pinch any wire harnesses or heater hoses.

155. Replace the recovery tank on the strut tower bolts,
then install and torque the strut tower nuts to 26 ft/lbs.

156. Reinstall the battery tray, battery, protective sleeve
and tie down strap, then secure the battery. Reconnect
the positive and negative clamps to their respective
terminals, and connect the new alternator power wire to
the positive battery terminal.

157. Turn the ignition key to the ‘ON’ position.

158. Verify that water is flowing briskly through the
recovery tank, then install the cap.

159. Have an assistant support the hood while you
tighten the four bolts that secure it to its hinges. Be
careful to verify that it is properly aligned and that the
supercharger has nothing on top of it before you attempt
to close the hood.

160. Reattach the washer nozzle hose and replace any
hood insulator body pins that were removed.

XV.  Flashing the ECU

161. Plug the supplied programming module into the
OBD-II port of the car, located below the steering column.

162. Once the main menu has loaded, press the central
‘select’ button on the controller to access the
‘Performance Tune’ option.

163. Read the discalimer carefully, then choose ‘Agree’
and press select.

164. Use the arrow buttons to select your transmission,
then press select to confirm your selection.

165. Select ‘Edelbrock E-Force 5psi’ from the menu.

Summary of Contents for E-Force 1580


































Reviews: