background image

Catalog #70080, #70081, #70082, #70083
Brochure No. 63-0312

©2008 Edelbrock Corporation

Rev. 07/08

Page 2

Thank You….
…for purchasing an Edelbrock Nitrous Oxide Injection System.

Nitrous Oxide injection is one of the most exciting performance enhancements, for the dollar invested, on the market today.
With the use of nitrous oxide come some important safety considerations. This manual has been written to help you during
the installation and use of your Edelbrock Nitrous System. Please read it completely before you install and use your
system. Please pay close attention to the safety information at the beginning of each section. The information contained
there specifically pertains to each of the components and installation methodologies within the section.

Please take the time to read and understand the following….

By installing your Edelbrock Nitrous System, you indicate you have read this document and you agree with the terms
stated below:

It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with
the Edelbrock Nitrous Systems. It is also the responsibility of the purchaser to determine the compatibility of the product
with the vehicle or the device on which the purchaser intends to install it.

Edelbrock Corporation assumes no responsibility for damages occurring from misuse, abuse, improper installation,
improper operation, lack of responsible care, or all previously-stated reasons resulting from incompatibility with other
manufacturer’s products and/or systems.

Edelbrock Corporation neither recommends nor condones the use of products manufactured or sold by Edelbrock
Corporation for use on vehicles, which may be driven on public roads or highways, and assumes no responsibility for
damages incurred by such use.

Edelbrock Corporation assumes no responsibility for damages incurred by the use of products manufactured or sold by
Edelbrock Corporation on vehicles used for competition or racing.

Edelbrock General Warranty

It is the constant endeavor of Edelbrock Corporation to give our customers the highest quality products obtainable.
Edelbrock warrants each new product, except Performer Series Carburetors, Race Division Parts, Tubular Exhaust Systems,
RPM Series Mufflers, Cat-Back Systems and Performer IAS Shock Absorbers which are warranted separately, to be free
from defects in both workmanship and material for a period of one (1) year from the date of purchase, provided that the
product is properly installed, subjected to normal use and service and that the product is not modified or changed in any
way, negligence by customer or installer or used for racing or competition purposes.

Our warranty service and repair facility is located at 2700 California Street, Torrance, California 90503. Customers who
believe they have a defective product should either return it to the dealer from which it was purchased or ship it directly
to Edelbrock along with proof of purchase and a complete description of the problem. The product must be returned
freight pre-paid. If a thorough inspection of the product by the factory indicates defects in workmanship or material, our
sole obligation shall be to repair or replace the product. Warranty covers only the product itself and not the cost of
installation or removal.

Edelbrock Corporation shall not be liable for any and all consequential damages occasioned by the breach
of any written or implied warranty pertaining to this sale in excess of the purchase price of the product sold.

If you have any questions regarding a product or installation, please contact our Technical Department, toll
free at 1-800-416-8628 from 7:00am to 5:00pm PST, Monday through Friday.

Thank you again for choosing Edelbrock Nitrous Systems.

Summary of Contents for 70080
































Reviews: