Edelbrock 3562 Installation Instructions Manual Download Page 14

Catalog #3562, 3563, 3564, 3565
Rev. 3/06

Page 14 of 16

©2006 Edelbrock Corporation

Brochure #63-0047

Note:

The fuel line will be a very tight fit over the 3/8" tubing.

It may be necessary to lube the tubing with some spray lubricant
to ease hose installation. Slip the 5/16" clamp over the rubber
hose, then insert fuel pump barb into hose and secure with 5/16"
clamp. Be sure there is adequate clearance between the metal
clamp and the electrical connections on the pump.

Some

shortening of the rubber hose may be necessary for proper
alignment of the pump with the pump hanger.

NOTE: DO NOT RE-USE THE ORIGINAL

IN-TANK FUEL HOSE OR CLAMPS.

New Hose

5/16”

5/16”

Clamp

3/8”

Clamp

Use the new rubber base gasket for fuel pump. If the big O-ring
in fuel tank is OK (not torn), you may reuse it. If necessary,
replace with original equipment O-ring from a GM dealer. Make
sure to grease large O-ring with white grease or equivalent.
Making sure clamp is tight and electrical connector is connected,
install strainer sock into same position (it will just push on with
your thumb).

Install complete assembly back in the fuel tank. Make sure you
do not bend anything while reinstalling. Lock assembly back in
place by rotating lock ring clockwise until it hits its stops. Now
tighten fuel connections and hose clamps.

Make electronic

connection and ground connection.

Re-install fuel tank

(Suburbans, etc.).

Do not re-install bed on pick-up trucks at

this time.   Before installing bed, see Fuel Pressure Test
Section on page 15.

29.

HOT RESTART FUEL MODULE

You must remove the Hot Restart Fuel Module before starting
your 1987-1989, over 8600 lbs. GVW HD vehicle. The Hot Restart
module is located on the Break Pedal Bracket between the
firewall, and the back of the gauge cluster. Its dimensions are
approximately 1-3/8” x 2-1/8” x 3-1/4”. There are three wires in
the harness for the Hot Restart Fuel Module;   a pink wire with a
black stripe, a black wire with a white stripe, and a tan wire with
a white stripe.

CAUTION:

iF THE HOT RESTART FUEL MODULE IS NOT

REMOVED, IT WILL OVERLOAD AND BURN ON START UP,
CAUSING SMOKE AND POSSIBLE FIRE HAZARD!

30.

NEW COMPUTER CHIP INSTALLATION

IMPORTANT NOTE: COMPUTER CHIP MUST BE

ORDERED BEFORE BEGINNING INSTALLATION.

Open glove box and remove four screws mounting the inner tray.
Remove glove box tray.

On the ECM, you will find the service number and the broadcast
code. Both are needed in order to make a new calibration chip
for your particular vehicle. This should be done well before
installation to allow enough time for the new chip to arrive. Use
the chip order card enclosed with these instructions.

After removing two screws and cover from ECM, remove old chip
by pressing down on the two outside retaining clips.

Summary of Contents for 3562

















Reviews: