©2010 Edelbrock LLC
Brochure #63-1551
Page 3
Edelbrock E-Force Supercharger Kits
Rev. 7/10 - AJ/mc
ADDITIONAL PARTS AND TOOLS
KIT CONTENTS
FOR STANDARD V-BELT DRIVE ACCESSORIES
❑
1
Supercharger/Manifold Top Plate Assembly
❑
1
Supercharger Intake Manifold
❑
1
Supercharger Snout Support/Idler Pulley Bracket
❑
1
Alternator Support Bracket
❑
1
Idler Pulley
❑
1
Idler Pulley Spacer
❑
1
Idler Pulley Nut
❑
1
Crankshaft Supercharger Drive Pulley
❑
3
Crankshaft Pulley Shim
❑
1
7/16-20 x 2.75” Long, 1.50” Shoulder Bolt (Crankshaft Balancer)
❑
3
3/8-24 x 3.75” Long, 2.625” Shoulder Bolt (Crankshaft Pulley)
❑
3
3/8-16 x 4” Long, 2.75” Shoulder Bolt (Idler Pulley and Bracket)
❑
10 3/8-16 x 1.25” Long Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑
2
3/8-16 x 1.75” Long, .625” Shoulder Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑
4
5/16-18 x 1.75” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑
4
5/16-18 x 2.5” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑
8
1/4-20 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
❑
4
5/16-18 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
Standard Bolt Pattern Kits Only
❑
3
3/8” I.D. Split-Lock Washer
❑
1
7/16” I.D. Split-Lock Washer
❑
1
7/16” I.D. x .120 Thick Flat Washer
❑
1
Supercharger Drive Belt
❑
1
Intake Manifold O-Ring Seal (54” Long)
❑
1
Intake Manifold Gaskets (Pair)
❑
1
Carburetor Kit (800CFM Thunder Series AVS, Electric Choke)
**
❑
1
Carburetor Stud, Nut, & Washer Kit
**
**
Carburetor and associated hardware included in certain kits ONLY.
See “Applications” section for those kits that include carburetor.
FOR BILLET SPECIALTIES TRU TRAC PULLEY SYSTEM
❑
1
Supercharger/Manifold Top Plate Assembly
❑
1
Supercharger Intake Manifold
❑
10 3/8-16 x 1.25” Long Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑
2
3/8-16 x 1.75” Long, .625” Shoulder Bolt (Intake Manifold)
Standard Bolt Pattern Kits Only
❑
4
5/16-18 x 1.75” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑
4
5/16-18 x 2.5” Long Bolt (Intake Manifold)
Vortec/E-Tec Bolt Pattern Kits Only
❑
8
1/4-20 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
❑
4
5/16-18 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)
Standard Bolt Pattern Kits Only
❑
1
Intake Manifold O-Ring Seal (54” Long)
❑
1
Intake Manifold Gaskets (Pair)
❑
1
Carburetor Kit (800CFM Thunder Series AVS, Electric Choke)
**
❑
1
Carburetor Stud, Nut, & Washer Kit
**
**
Carburetor and associated hardware included in certain kits ONLY.
See “Applications” section for those kits that include carburetor.
TOOLS AND EQUIPMENT:
❑
Box and open end wrenches
❑
Socket set
❑
Distributor wrench
❑
Pliers (channel locks and hose clamp)
❑
Screw drivers (regular and Phillips)
❑
Torque wrench
❑
Hammer
❑
Gasket scraper or putty knife
❑
Timing light
❑
Vacuum gauge
❑
Rags
❑
Water bucket
❑
Paper and pencil
ADDITIONAL PARTS AND SUPPLIES:
❑
Gaskets-Edelbrock, or performance gasket equivalent
❑
Pipe plugs, if needed
❑
Edelbrock Gasgacinch (#9300)
❑
RTV High Temp silicone sealer or O/2 sensor safe RTV
❑
Masking tape
❑
Modeling clay or putty
❑
Chalk
❑
Radiator coolant
❑
Teflon thread tape or PST thread sealer or equivalent
❑
Thread locking compound such as Loctite™ (Red, Blue, or
equivalent)
❑
Supercharger & Accessory drive belt (for Billet Specialties
applications, see installation procedure for recommended part
numbers)
IMPORTANT NOTE:
Edelbrock E-Force Supercharger kits do not include
the Billet Specialties Tru Trac Pulley System. These systems are available
seperately from Edelbrock and include a water pump, A/C compressor,
drive belt, alternator, and all the pulleys, brackets, and mounting
hardware necessary for a complete installation. These systems can be
purchased with a power steering pump as part #1565, or without as part
#1566.
