manualshive.com logo in svg

Eddyfi Technologies INUKTUN VT100, Manual, Page: 25 / 28

Share
Download
Eddyfi Technologies INUKTUN VT100 Manual Download Page 25

 

VT100 Vertical Crawler™ 

 

Document: UMAH000514.docm  

Revision: A14 

Created by: PJ 

Date: 05 Dec 2019 

3029669-A14 

Source Location: C:\ePDM\ISLEng\products\ah-versatrax100\manuals\UMAH000514.docm

 

 

Page 25 of 28 

 

 

User Ma

nual

 

Fuse Replacement  

The controller and power supply contain panel mount fuses for both AC and DC voltages. These fuses 
are for the safety of the operator(s) as well as to protect the equipment from damage. If a fuse blows, stop 
and look for possible causes. Causes might include cable damage, water incursion or improper 
connections. 

See the controller manual for fuse replacement. 

Fuse values have been carefully selected for their application. Always replace the fuses with the same 
type and rating. 

 

WARNING:

 Disconnect the power source before checking or replacing fuses. 

 

Microtrac™ Maintenance 

Refer to the Microtrac

™ manual for Microtrac maintenance and servicing instructions.  

Camera Maintenance 

Refer to Spectrum 45

™ manual for camera operation and maintenance instructions.

 

Tether Re-termination 

Contact us if tether re-termination is required. Tether re-termination kits are also available. Detailed 
instructions and wiring diagrams will be included with the kit.  

 

Summary of Contents for INUKTUN VT100





























Reviews:

No comments