manualshive.com logo in svg

Edco VAC-200, Operator'S Instruction Manual, Page: 6 / 11

Share
Download
Edco VAC-200 Operator'S Instruction Manual Download Page 6

E-VAC290&VAC200-I-1017

Printed in USA
©2017 

Page 6

Standard Filter Installation VAC-200

1. Turn the filter housing spacer assembly over on a table then fit the filter over the filter shaker insert.

2. Make sure each pleat is fully supported and the ground wire is on the filter side of the assembly.

3. Connect the filter housing spacer assembly ground wire to the base via the push–on terminal.

4. Seat the filter housing spacer assembly on the base oriented as it was removed.

5. Seat the reverse pulse/motorized shaker assembly and housing spacer (if so equipped) on the filter housing spacer

assembly oriented as removed; make sure to connect the component ground wire to the filter housing spacer assem

-

bly via push-on terminal.

6. Seat the HEPA adapter assembly and housing spacer (if so equipped) on the preceding housing component

oriented as removed; make sure to connect the component ground wire to the preceding assembly via push on

terminal.

7. Connect the motor deck ground wire to the preceding assembly.

8. Connect the three power cord wires to the their respective terminals in the terminal block on the underside of the

motor deck.

9. Seat the motor deck on the preceding housing spacer.

10. Connect the clear differential pressure gauge tubes to their respective barbed fittings if so equipped.

11. Turn the machine on then block the inlet with a flat and rigid material to place the machine under vacuum

pressure.

12. Secure all of the housing-components then turn the machine off.

HEPA 2.0 Filter Replacement Procedure VAC-200

1. Turn the machine on then block the inlet with a flat

rigid material to place the machine under vacuum pressure.

2. Remove hardware, motor deck and motors.  Remove ground

wire if necessary.

3. Turn assembly over.

4. Remove lock nut, nut, and washer on each cartridge.

5. Remove cartridge filter.

6. Install cleaned or new cartridge and re-assemble hardware.

7. Reinstall motor deck. Attach ground wire.

8. Turn on motors and block inlet to compress the housings.

9. Reinstall hardware.

Discount-Equipment.com

Summary of Contents for VAC-200












Reviews:

No comments