manualshive.com logo in svg

EDAN INSTRUMENTS SE-3, Service Manual, Page: 32 / 47

Share
Download
EDAN INSTRUMENTS SE-3 Service Manual Download Page 32

SE-3 3-Channel Electrocardiograph Service Manual 

-27- 

Chapter 6 Electrocardiograph Installation 

CAUTION

: 

Before use, the equipment, patient cable and electrodes should be checked. Replace it if 

there is any evident defectiveness or aging which may impair the safety or performance. 

And be sure that the equipment is in proper working condition. 

6.1 Power and Earthing 

WARNING

: 

 

If the integrity of external protective conductor in installation or arrangement is in doubt, 

the equipment should be operated from the built-in rechargeable battery.

 

Power Supply 

The  electrocardiograph  can  be  powered  either  by  mains  supply  or  the  built-in  rechargeable 

lithium battery pack. 

1. Mains supply 

The mains connection socket is on the left of the unit. If mains supply used, connect the power 

cord to the socket first, and then connect the plug of the cord to the hospital grade outlet.   

Rated input voltage:    100V~115V or 220V~240V 

Rated frequency:   

 

50Hz/60Hz 

Rated input power:      35VA 

Make sure the mains supply meets the above requirements before power on. And then press the 

mains power switch to power on the unit. Then the mains supply indicator lamp (

) will be lit. 

If  the  built-in  rechargeable  battery  is  weak  when  mains  supply  used,  it  will  be  recharged 

automatically  at  the  same  time.  And  both  the  mains  supply  indicator  lamp  (

)  and  the  battery 

recharging indicator lamp (

) will be lit. 

2. Built-in rechargeable battery 

While using the built-in rechargeable lithium battery pack, turn on the unit by pressing 

ON/OFF

 

key on control panel directly and the battery indicator lamp (

) will be lit.   

The  battery  symbol 

  will  be  displayed  on  the  LCD  screen.  Because  of  the  consumption 

during storage and transport, the capacity of battery may not be full. If the symbol 

  and the 

hint information 

“

BAT WEAK

”

 are displayed, which means the battery capacity is weak, please 

Summary of Contents for SE-3
















































Reviews:

No comments