manualshive.com logo in svg

ECS Z97I-DRONE, User Manual

Share
Download
ECS Z97I-DRONE User Manual Download Page 21

Chapter 2

15

Z97I-DRONE USER MANUAL

Install the VGA Card in the PCIEX16 slot

1

Remove a blanking plate from the system case corresponding to the slot

you are going to use.

2

Install the edge connector of the add-on card into the expansion slot.

Ensure that the edge connector is correctly seated in the slot.

3

Secure the metal bracket of the card to the system case with a screw.

For some add-on cards, for example graphics adapters and network
adapters, you have to install drivers and software before you can begin using
the add-on card.

Follow these instructions to install an add-on card:

Please refer the following illustrations to install the add-on card:

Install the LAN Card in the PCIE slot

Please refer the following steps to install the M.2 Wifi/ Bluetooth card:

1

Demount the screw not used according to the length of your 

M.2 Wifi/

Bluetooth card

2

Insert the M.2 Wifi/ Bluetooth card into NGFF slot in the fool-proof way.

Summary of Contents for Z97I-DRONE





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands