ECS 945GCT-M3 Manual Download Page 31 | Manualshive

Page: 31 / 60

ECS 945GCT-M3 Manual Download Page 31

Installing the Motherboard

25

Connecting Case Components

After you have installed the motherboard into a case, you can begin con-
necting the motherboard components. Refer to the following:

1

Connect the CPU cooling fan cable to

CPU_FAN

.

2

Connect the system cooling fan connector to

SYS_FAN

.

3

Connect the case switches and indicator LEDs to the

PANEL1

.

4

Connect the standard power supply connector to

ATX1

.

5

Connect the auxiliary case power supply connector to

ATX12V

.

6

Connect the case cooling fan connector to

CHS_FAN

.

24-pin power cable

When installing 4-pin power cable, the
latches of power cable and the ATX12V
match perfectly.

4-pin power cable

With ATX v2.x power supply, users please
note that when installing 24-pin power
cable, the latches of power cable and the
ATX1 match perfectly.

The ATX 24-pin connector allows you to connect to ATX v2.x power
supply.

Connecting 4-pin power cable

The ATX12V power connector is used to provide power to the CPU.

Connecting 24-pin power cable

«
...
29
30
31
32
33
...
»

Summary of Contents for 945GCT-M3





























































Reviews:

No comments