manualshive.com logo in svg

ECS 845PE-A800, Manual, Page: 58 / 70

Share
Download
ECS 845PE-A800 Manual Download Page 58

Multi-Language Translation

Itallano

La scheda madre è dotata di un set completo di connettori e porte I/O:

• 

Due porte PS/2 per mouse e tastiera

• 

Una porta seriale

• 

Una porta parallela

•       Sei porte USB (4 porte sul pannello I/O posteriore, 1 testata che supporta 

2 porte sulla scheda)

• 

Una porta LAN (opzionale)

• 

Jack audio per microfono, linea d’ingresso e linea d’uscita

LAN Onboard (opzionale)

I/O integrato

Questa scheda madre adotto un BIOS Award che permette agli utenti di configurare le 

caratteristiche principali del sistema, inclusi:

• 

Gestione energia

• 

Parametri CPU

• 

Temporizzazione CPU e memoria

Il firmware può anche essere usato per impostare i parametri per diverse velocità di clock.

Alcune specifiche hardware e software potrebbero essere soggette a 

cambiamenti senza preavviso.

Firmware BIOS

Il chip per LAN è incorporato nella serie di chip della scheda madre e mette a disposizione un 

controller Ethernet con velocità di 10/100 Mbps e funzionalità PCI LAN Ethernet integrate.

•      Supporto operazioni di auto negoziazione N-Way a 10Mb/s e 100Mb/s
•      Supporto di funzionalità half/full duplex
•      Supporto funzione WOL (Wake-On-LAN) e riattivazione remota

Summary of Contents for 845PE-A800







































































Reviews:

No comments