background image

   

 

       

 

 

 

 

 

Quick Start USER GUIDE

 

 

 

 

SAFETY

 

This product has a limited life span of use and should be replaced when it shows obvious signs of wear.  

 

Do not modify or remove any original component parts of the speaker. Doing so could cause damage to the unit allowing water to ingress.  
A unit with water ingress should not be charged due to potential risk of fire or shock.   

 

Do not attempt to mount the unit except with the approved ECOXGEAR mounts. Doing so could cause damage to the unit allowing water to 
ingress. A unit with water ingress should not be charged due to potential risk of fire or shock.   

 

Please exercise care and good judgment when using your ECOXGEAR speaker.  Audio levels should be appropriate to your environment, comply 
with all local regulations, and always ensure that you can hear and be aware of any potential hazards around you.   

 

 You should always 

1)

 

Use the ECOXGEAR speaker in accordance with any music or noise rules and regulations.  

2)

 

Use the proper ECOXGEAR mounts if you intend to mount the unit.  

3)

 

Properly seal the ECOXGEAR 

prior and after

 each use when in humid or water environments to avoid water damage to the internal 

components.   Salt water / air is particular corrosive. Always make sure that the gasket are sealed when in salt water environment and the 
unit properly rinsed off after use.  

4)

 

Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt or water on them prior to storage or removing the back cover.  

5)

 

Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit.  

6)

 

Completely dry and clean your ECOXGEAR prior to attempting to charge the unit.  

7)

 

Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe impact that may 
have affected the integrity of the unit to take on water.  

 

 

You should never 

1)

 

Charge your ECOXGEAR if you suspect water has entered the device. Charging a device with water inside could be potential hazardous and 
cause fire or a spark.  

2)

 

Use your ECOXGEAR if you have dropped it or thrown it against a hard surface which may have destroyed the integrity of the speakers, 
housings or gaskets. In the event of a severe impact to your unit please return the unit to Grace Digital to review for potential damage.  

3)

 

Open the auxiliary door in a water environment. This could cause water to ingress into the unit which could potentially be hazardous and 
cause a fire or a spark. 

4)

 

Connect a device to the auxiliary input jack when in a water environment. The auxiliary jack should only be used in a dry environment.  

5)

 

Attempt to fix, repair your ECOXGEAR unit. Please send it back to Grace Digital for any assessments and repairs. 

 

 

Summary of Contents for GDI-EGST700--710












Reviews: