background image

EcoNet

®

 Smart Thermostat User Guide  

26

> Return to Table of Contents

Mounting EcoNet Smart Thermostat

1.  Turn off all power to equipment (e.g. furnace or air handler and outdoor unit).

2.  If an existing thermostat or control is being replaced:

 

a. Remove existing control from wall.

 

b. Disconnect wires from existing control.

3.   Place the provided ferrite toroid around the thermostat wires and nest in the drywall. It is suggested to place a 

zip tie on the thermostat wire to prevent the ferrite toroid from sliding too far back. (See Fig. 1)

  Note: 

A ferrite toroid is a magnetic core made of ferromagnetic material. It is used for its properties of high magnetic permeability coupled 

with low electrical conductivity to help reduce radio frequency emissions that can interfere with other devices.

4.  Position the back plate of your EcoNet Smart Thermostat on your wall, using the built-in level to make sure  

 

it’s straight. Mark the mounting holes on your wall in pencil.

5.  Drill mounting holes for the drywall anchors and insert.

Note: 

It is recommended you fill the hole around the thermostat wires with light insulation to prevent draft.

6.  Route wires through hole in wall plate plastic. Use the screws provided to secure the back plate to the wall.  

(See Fig. 2)

7.  Match and connect thermostat wires to proper terminals on back plate. (See Fig. 3)

Note: 

the wire color used for each terminal, as it is good practice to use the same wire color on identical termination points on the indoor 

and outdoor units.

8.  The wires from the wall should plug easily into the terminal blocks. To release a wire, press down on the lever. 

When installed correctly, the release lever of the terminal block will lower to indicate engagement.

9.  Push any excess wire back into the wall. Seal hole in wall to prevent any air leaks. Leaks can affect operation.

10. Attach EcoNet Smart Thermostat to the secured wall plate using alignment guides. (See Fig. 4)

11. Perform installation of all other system equipment.

12. Turn power to equipment back on.

Note: 

To avoid nuisance alarms, power outdoor unit prior to indoor unit.

(Fig. 2)

(Fig. 3)

QUICK S

TART 

GUIDE

E1
E2

C

R

R

E1
E2

S1
S2

C

R

E1
E2

C

OUTDOOR UNIT

INDOOR UNIT

OPTIONAL REMOTE

TEMPERATURE SENSOR

ECONET 

SMART THERMOSTAT

R   C   S1   S2  E1  E2

(Fig. 4)

QUICK S

TART 

GUIDE

E1
E2

C

R

R

E1
E2

S1
S2

C

R

E1
E2

C

OUTDOOR UNIT

INDOOR UNIT

OPTIONAL REMOTE

TEMPERATURE SENSOR

ECONET 

SMART THERMOSTAT

R   C   S1   S2  E1  E2

QUICK S

TART 

GUIDE

E1
E2

C

R

R

E1
E2

S1
S2

C

R

E1
E2

C

OUTDOOR UNIT

INDOOR UNIT

OPTIONAL REMOTE

TEMPERATURE SENSOR

ECONET 

SMART THERMOSTAT

R   C   S1   S2  E1  E2

QUICK S

TART 

GUIDE

E1
E2

C

R

R

E1
E2

S1
S2

C

R

E1
E2

C

OUTDOOR UNIT

INDOOR UNIT

OPTIONAL REMOTE

TEMPERATURE SENSOR

ECONET 

SMART THERMOSTAT

R   C   S1   S2  E1  E2

(Fig. 1)

View from 

behind wall

Summary of Contents for UETST700SYS






































































Reviews: