10
As an example, if you have a home office and you want to warm it up during
the day on weekdays only, you can program the following times:
Monday to Friday
from 00:00 to 08:30 17°C
from 08:30 to 17:00 21°C
from 17:00 to 23:59 17°C
Saturday and Sunday
from 00:00 to 23:59 7°C
During normal operation, the display shows
switching periods, the humidity, the internal
temperature, mode of operation,
programmed temperature & day of the
week. The columns in the weekly program
are displayed for alternate time intervals. An
example is shown in section 9 – Weekly program - examples.
At the top of the display you can also show values that are not related to
internal temperature and humidity. The values on the display can be
changed with the Display button. For instance, with a wirelessly
connected external sensor, you can record the external minimum and
maximum temperatures.
Pressing for more than 3 seconds on the display button you can delete
the stored minimum and maximum values for the external temperature
readings.
.
Once a week movement of the pin is activated to prevent the formation
of scale on the valve. The time and the start date can be changed
(default is Saturday at 12:00).
•
Press the Menu button for more than 3 seconds.
•
Select the menu item “CAL” with the setting dial.
•
Confirm with OK.
•
Select the day of the week with the setting dial.
•
Confirm with OK.
•
Select the time with the setting dial.
•
Confirm with OK.
If you have assigned a window contact to the wall thermostat, this
lowers the temperature automatically when you ventilate the premises,
allowing you to save on heating costs. A display shows the Window Open
symbol
( )
. The target temperature when the window is open, can be
set as desired:
•
Press the Mode button for more than 3 seconds.
•
Select the menu item “AER” with the setting dial.
The components of the system need to be paired so that they can
communicate with each other by radio transmission. Proceed as follows:
•
First set the radiator controller in the pairing mode. Read the
instructions for this in the relevant manual.
•
The wall thermostat transmits a radio signal. Press the OK button on
the wall thermostat for more than 3 seconds.
•
The display shows “LEA” and the pairing time remaining (up to 30
seconds), while the wall thermostat sends a radio signal.
•
If the controller receives the signal, its display shows “ECF”.
The wall thermostat can be paired with different regulators.
If the radio communication should be interrupted, the
controller continues to control the temperature
independently, according to the last setting on the wall
thermostat.
After you have replaced the batteries in the controller, it may
take up to an hour and a half before the actuator receives
new data from the wall thermostat and switches to “ECF”.
•
Confirm with OK.
•
Set the temperature with the dial.
•
Confirm with OK.
You can manually reset the factory settings of the wall thermostat. All
settings made manually will be lost.
•
Press the Menu button for more than 3 seconds.
•
Select the menu item “RES” with the setting dial.
•
Confirm with OK.
•
The display shows “ACC”, confirm with OK.
The controls can be locked.
•
To enable or disable the control lock , simultaneously press the
Mode
and
buttons.
•
The display then shows “LOC”.
•
To de-activate the function, press both keys again.
When the heating is turned off during the Summer, you can minimise
reduction in battery life. The valve is fully open and limescale
protection remains active.
•
To activate the heating phase, turn the setting dial clockwise if in
manual mode (
Manu
), until the display shows “ON”.
•
To end the function, exit manual mode or turn dial anti-clockwise.
In pairing mode, up to 5 components of the system (e.g. remote
control, window contact, external sensor) can be wirelessly connected
to the wall thermostat.
•
Press the OK button for more than 3 seconds.
•
Display shows “LEA” and the pairing time remaining (up to 30
seconds)
•
The component must now be put into pairing mode (e.g. for a
remote control, press a button).
•
After pairing, the assigned unit is displayed for 3
seconds on the wall thermostat display (RC – remote
control, SC – window contact, OT – outdoor temperature
sensor).
•
The display will then return to normal.
If the wall thermostat is already connected to 5 devices, the display
will show “Err” if an attempt is made to add a further device. Before
proceeding with the assignment of a new device, you should delete
those already assigned (see section 14).
You can delete the assignment of components on the wall thermostat
with the “UNL” function. All the paired components assigned are
deleted at the same time.
•
Press the Mode button for more than 3 seconds.
•
Select the menu item “UNL” with the setting dial.
•
Confirm with OK.
•
The display shows “ACC”, confirm with OK.
If the room does not have to be heated, radiator valves can be closed.
The valve is opened only in case of frost.
Limescale protection remains active.
•
Turn dial anti-clockwise, decreasing temperature when in the
manual mode (
Manu
), until the display shows “OFF”.
•
To end the function, exit manual mode (
Manu
) or press the right
arrow key ( increase temperature).
Do not throw away the device with the normal
household waste!
Electronic equipment must be disposed of in accordance
with the legislation on used electrical and electronic
equipment and be delivered to a collection point.
The CE mark does not represent a guarantee of device
characteristics.
These devices are not toys, so prevent children playing with them. Do
not leave unattended packaging material because it could pose a
danger to children. Never open the unit as it does not contain any
parts that can be repaired by the user. In case of damage, send it to
the service centre.
With the Comfort & Low Temperature(
) button, you can simply
switch between these two temperatures. Factory setting
for temperatures is 21°C and 17°C respectively, which can
be changed in the following way:
•
Press and hold Comfort & Reduced (
) button.
•
A display shows the Sun symbol (
) and the current comfort
temperature.
•
Adjust the temperature with the setting dial and confirm with OK.
•
The Moon symbol (
) appears, with the reduced temperature .
•
Adjust the temperature with the setting dial and confirm with OK.
Even in automatic mode, the temperature can be changed at any time
with the button. The temperature setting is saved until the next
switching point of the program.
If you are on holiday and want to maintain a certain temperature in
the premises, you can use the Holiday function.
•
Press and release the Menu button until the display shows the
suitcase symbol (
).
•
Then set the dial until the return time is displayed.
•
Confirm with OK
•
Then set the return date with the dial.
•
Confirm with OK.
•
Set the temperature with the dial and confirm with OK.
The actuator gives a confirmation blink. The set temperature
is stored until the set return date and time. The actuator then
switches to automatic mode.
The radio transmission takes place on a non-exclusive transmission
channel, and interference of signal cannot be ruled out. Noise can be
experienced from the switching on and off of electric motors in the
vicinity.
The signal range within buildings can be very different from that in
open space. In addition to the transmission and reception
characteristics of the receiver, climatic factors such as moisture or site
conditions have an effect.
Power supply:
3 V
Current consumption max.:
30 mA
Batteries:
2 off LR6 (AA/AA)
Battery life:
2 years approx.
Display:
LCD
Frequency:
868,3 MHz
Range (Open):
20 m
Case size:
78 x 98 x 28 (W x H x D)
Subject to technical changes for product improvement.
24. Safety instructions
23. Disposal instructions
22. Setting the frost protection mode
21. Heating switched off
20. Child lock / Key lock
19. Reset to factory settings
18 – Open window / ventilation function
17. Setting the de-calcification routine
14. Deleting paired components
13. Pairing of wall thermostat
15. Comfort and reduced temperature
11. Changing the values
26 – Specifications
25. Guidelines for wireless mode
16. Holiday settings
12. Pairing the controllers wirelessly to save
energy
10. Display content in normal operation
11
15
16
9
12
14
13
10
