ECKELMANN Virtus 5 Series Operating Instructions Manual Download Page 95 | Manualshive

Page: 95 / 183

background image

Firmware V7.16.x

16.05.2023

95/183

1.

2.

•

•

•
•
•

9.1.1.1 Status bar and quick info

Button No.

Function

1

Home - display main menu, only visible in submenus

2

Back - one menu level back, only visible in submenus
Exception: If the diagram of the 24h list is open, this button jumps back to the main menu! If
you would only like to return to the table form view of the 24h list, the button at the bottom left
in the navigation area must be tapped.

3

Call of context-related information and explanations for the respective displayed menu or entry
screen,only visible if information is available.

4

Audible alarm (internal buzzer or optional external horn on the AUX relay); to switch off alarm,
see chapter

.

5

There are pending alarms and messages! Tap to open alarm and message list, see chapter

Menu 1 1 Alarms and messages

.

6

VNC connection activ

7

Display list of failed refrigeration points (only visible if refrigeration points have failed).

By tapping on the refrigeration points shown in the list, they can be

defined as unloaded: refrigeration points that have either been switched off, e.g. for
cleaning, and should be switched on again later,
or
are defined as failed: if the cause for why refrigeration points have failed is unknown,

e.g. when a fault is present.

For details, see chapter

Alarm suppression for manual shutdown of case controllers

.

8

Service mode for suppression of remote alarm signalling. The following displays are possible:

white: activation of the service mode by entry of a time in the range of 0 - 255 minutes
NOTE: This button is not displayed until

after

successful login to the device.

yellow: indicates that Service Mode is activated.

For details about Service Mode, see chapter

Service Mode - Suppression of remote alarm

9

Login to the system centre (unlocking)

white: login possible
yellow: user is logged in
white and red crossed out:

For details, see chapter

Login to the system centre (unlocking)

.

a login or logout is not possible.

«
...
93
94
95
96
97
...
»

Summary of Contents for Virtus 5 Series
























































































































































































Reviews:

No comments

Related manuals for Virtus 5 Series

Brand: C&K systems Pages: 2

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 42

Brand: Banner Pages: 15

Brand: bar Pages: 2

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

Brand: ECKELMANN Pages: 178

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: Omegalink Pages: 2

Brand: Omega Pages: 56

Brand: Omega Pages: 2

Brand: We Care Solar Pages: 46

Brand: Watts Pages: 4

OneFlow OFTWH-R

Brand: Watts Pages: 8

Brand: Vaillant Pages: 12

Brand: Sunnen Pages: 24

Q Module WFZ16.Ox

Brand: QUNDIS Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands