ECKELMANN Virtus 5 Series Operating Instructions Manual Download Page 36 | Manualshive

Page: 36 / 183

background image

Firmware V7.16.x

16.05.2023

36/183

5.7 M-bus Interface for Consumption Data Capture

The M-bus (meter bus) is a fieldbus for the capture of e.g. gas, water or power consumption data. The data are
transmitted serially from the connected meters (slaves / field devices) to an M-bus gateway (master) on a
reverse-polarity protected twin wire cable. The M-bus gateway itself is connected to the COM2 interface of the
system centre:

Daily consumption values are recorded for each M-bus meter in the system at the factory. The daily
consumption values can be displayed in the menu 6-1. The option "Performance Calculation" must be set in the
menu 4-1-6 for the display of a load profile (consumed capacity in the last 15 minutes). The load profile can
then be displayed in menu 6-2.

Configuration of the measuring points

New measuring points connected to the M-bus are found using a scan process and included in the system. The
scan process is started in menu 4-1-6 using the following button:

If new measuring points have been found by the scan process, these are then displayed in the list and can be
configured

. An overview of the supported M-bus meters can be found here:

https://edp.eckelmann.de/edp/lds/_dGFHqz89xb

For detailed information, see chapter

M-bus - Connection of gateways

.



«
...
34
35
36
37
38
...
»

Summary of Contents for Virtus 5 Series
























































































































































































Reviews:

No comments

Related manuals for Virtus 5 Series

615 Series ANSI

Brand: ABB Pages: 60

Minas A4 Series

Brand: Panasonic Pages: 5

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: IBC Pages: 8

Brand: Partizan Pages: 7

Brand: A.R.I. Pages: 14

Brand: Industrial Controls Pages: 17

Brand: SolarEdge Pages: 20

Brand: Greenheck Pages: 4

Brand: Hach Pages: 504

Brand: National Instruments Pages: 26

Brand: Waeco Pages: 168

Brand: Waterbird Pages: 19

MOBA-Matic MMC-1000

Brand: MOBA Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands