EchoStar HUGHES inmarsat 9502 User Manual Download Page 75 | Manualshive

Page: 75 / 77

background image

Chapter 8 •

Regulatory notices

3500834-0001 Revision C

75

Chapter 8

Regulatory notices

EU Declaration of Conformity

Refer to

www.bgan.hughes.com

for the EU Declaration of Conformity.

FCC compliance /

Conformité FCC

This device conforms to the FCC rules. Any changes or modifications to Hughes

Network Systems’

equipment, not expressly approved by Hughes Network Systems,

could void the user's authority to operate the equipment.

Cet appareil est conforme aux règles FCC. Toute modification apportée à

l’équipement de Hughes Network Systems et

non approuvé expressément par

Hughes Network Systems, peut annuler l’autorisation de l’utilisateur à opérer cet

équipement.

To comply with FCC RF exposure requirements, this device must be operated with a
minimum separation distance of one meter from the

front of the satellite terminal’s

antenna to a person's body. Other operating configurations should be avoided.

Afin d’être conforme aux exigences FCC concernant l’exposition RF, cet appareil doit

être utilisé tout en maintenant une distance de séparation

minimale d’un mètre

entre la personne et le devant de l’antenne du terminal satellite.

Toute autre

configuration d’utilisation doit être évitée.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions; (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Cet appareil est conforme à la Section 15 du règlement FCC. Son fonctionnement est
sujet aux deux conditions suivantes; (1) ce matériel ne peut pas provoquer

d’interférences nuisibles, et (2) ce matériel doit pouvoir tolérer n’importe quelle

interférence reçue, y compris les interférences qui peuvent provoquer un
fonctionnement indésirable.

IC compliance /

Conformité IC

This device conforms to Industry Canada's rules. Any changes to Hughes Network
Systems' equipment, not expressly approved by Hughes Network Systems, could
void the user's authority to operate the equipment.

Cet appareil est confor

me aux règlements de l’Industrie Canada. Tout changement à

l’équipement de Hughes Network Systems, sans le consentement exprès de Hughes
Network Systems, peut résulter à l’annulation de l’autorité confiée à l’usager
d’opérer cet équipement.

«
...
73
74
75
76
77
»

Summary of Contents for HUGHES inmarsat 9502














































































Reviews:

No comments

Related manuals for HUGHES inmarsat 9502

Brand: WAGO Pages: 46

Brand: Samson Pages: 45

Brand: Bogen Pages: 12

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 15

Brand: Iluv Pages: 40

LTC 4600 Series

Brand: Bosch Pages: 24

Brand: Bosch Pages: 36

CMT-M70 Primary

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brand: Sony Pages: 36

Brand: Sony Pages: 36

Brand: Sony Pages: 68

CMT-GPX6 - Micro Hifi Component System

Brand: Sony Pages: 74

Brand: Sanyo Pages: 16

Brand: Sanyo Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands