Milestone AV Technologies and its affi
liated corporations and subsidiaries (collectively,
“Milestone”), intend to make this manual accurate and complete. However, Milestone
makes no claim that the information contained herein covers all details, conditions, or
variations. Nor does it provide for every possible contingency in connection with the
installation or use of this product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone makes no representation
of warranty, expressed or implied, regarding the information contained herein.
Milestone assumes no responsibility for accuracy, completeness or suffi
ciency of the
information contained in this document.
©2015 Milestone AV Technologies. All rights reserved. ECHOGEAR is a Milestone
brand.
ECHOGEAR and the ECHOGEAR logo are trademarks of Milestone.
Made in China.
Milestone Global Headquarters
• 6436 City West Parkway • Eden Prairie, MN 55344 USA
6901-002430 02
07
Adjustments
[S]
To adjust TV
tilt, loosen the
handle on the
arm plate, tilt
TV to desired
angle, and
retighten
handle to
secure.
To adjust arm
tension, use a 6 mm hex key (not included).
To adjust TV level, loosen screws
[S]
on the rear of
the arm plate, adjust level, and retighten to secure.
6 mm
Drill two pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit.
IMPORTANT
: Be sure to drill into the center of the
stud.
IMPORTANT
: Pilot holes must be drilled to a depth
of 3 in. (75 mm).
01
01
01
01
5-1
5-2
5-3
5-4
Locate your
stud. Verify
and mark
the center of
the stud by
fi nding the
stud edges
using an awl,
a thin nail,
or an edge-
to-edge stud
fi nder.
Position the wall plate
01
at your desired height
and line up the holes with your stud center line.
Level the wall plate and mark the holes.
IMPORTANT
: Be sure to only use the top hole and
bottom slot for mounting.
Hang TV onto arm
and using hex key
07
, secure with
screws
[S]
saved
from
Step 1
.
IMPORTANT
:
These screws
[S]
must
be installed to
secure the TV onto
the arm
01
.
07
[S]
05
06
05
06
Step 6
Step 5 Wood Stud
Flat Back
Round Back / Extra Space
CAUTION:
Avoid potential personal injuries
and property damage!
●
Drywall covering the wall must not exceed
5/8 in. (16 mm)
●
Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
CAUTION:
Avoid potential personal injury or
property damage! All lag bolts
05
MUST BE firmly
tightened to prevent unwanted movement of the
wall plate
01
.
CAUTION:
Ensure the wall plate is securely
fastened to the wall before continuing on to the
next step.
3 in. (75 mm)
7/32 in.
(5.5 mm)
M4 M6 M8
Select Your TV Screws
CAUTION:
Verify thread
engagment of the screw or spacer/
screw combination.
— Too short will not hold the TV
— Too long will damage the TV.
Correct
Too Short
Too Long
Note Orientation
Position your TV bracket
configuration (
A
or
B
)
over your TV hole pattern
- making sure the bracket
is centered over the TV
hole pattern and level.
Secure bracket using your
screw/washer (
Flat Back
)
or spacer/screw/washer
(
Round Back / Extra
Space
) selection.
CAUTION:
Ensure
TV bracket is securely
fastened before moving on
to the next step.
14
10
15
15
17
11
16
16
09
13
08
12
Step 4
Install wall plate
01
using lag bolts
05
and
washers
06
. Tighten the lag bolts
05
only until
they are pulled firmly against the wall plate
01
.
