manualshive.com logo in svg

Echo WP-1000, Operator'S Manual

Share
Download
Echo WP-1000 Operator'S Manual Download Page 29

WP-1000

TROUBLESHOOTING

© 4/2015 ECHO Inc.

X7505120800

29

TROUBLESHOOTING PUMP END

No water delivered or not 
enough water delivered 

•Pump not primed

•Fill pump body with water. 

•Speed too low

•Pump should operate at 5600-6300 rpm. 

•Clean suction opening. 

•Suction line clogged

 •Locate pump closer to water.

•Suction lift too high

•Tighten connections or replace with new 
hose or pipe.

•Air leak in suction line

Use pipe compund to seal threads.

 

•Impeller plugged.  

•Clean impeller. 

•Suction end not submerged deep 
enough. 

•Submerge suction hose or piping enough 
so no air enters while pump is operating.

Not enough pressure

•Speed too low.

•Engine should operate at 5600-6300 rpm.  

•Worn impeller. 

•Replace impeller.

Pumps water, then stops

•Suction line out of water.

 •Lower suction line into water.                                                                                                                                               

•Suction lift too high.

•Locate pump nearer water.

•Pump clogs with debris.

•Clean pump and impeller.

•Suction strainer clogs.

•Clean strainer.

•Pump seal worn.

•Replace seal. (ECHO Dealer)

Pumps water, then stops 

•Foreign matter settled or solidified 
inside the pump.

•Remove pump casing and clean the pump

•Impeller is clogged by solid debris.

Summary of Contents for WP-1000









































Reviews:

No comments

Brands by name

Popular brands

Load more brands