background image

SRM-266/S

TROUBLESHOOTING

© 3/2013 ECHO Inc.

X7502026002

29

TROUBLESHOOTING

 Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition 
spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may 
result.

ENGINE PROBLEM TROUBLESHOOTING CHART

Problem Check 

Status 

Cause 

Remedy 

Engine cranks - 
starts hard/ 
doesn’t start 

Fuel at carburetor

No fuel at carburetor

Fuel strainer clogged
Fuel line clogged 
Carburetor 

Clean or replace
Clean or replace
See your Echo dealer 

Fuel at cylinder

No fuel at cylinder 

Carburetor 

See your Echo dealer 

Muffler wet with fuel 

Fuel Mixture too rich 

Open choke 
Clean/replace air filter 
Adjust carburetor 
See your Echo dealer 

Spark at end of 
plug wire

No spark

Stop switch off 
Electrical problem
Interlock switch

Turn switch to ON 
See your Echo dealer 
See your Echo dealer 

Spark at plug

No spark

Spark gap incorrect 
Covered with carbon 
Fouled with fuel
Plug defective

Adjust to .65mm (0.026 in.)
Clean or replace 
Clean or replace 
Replace plug 

Engine runs, 
but dies or 
does not 
accelerate 
properly 

Air filter 

Air filter dirty

Normal wear 

Clean or replace 

Fuel filter 

Fuel filter dirty

Contaminants/residues 
in fuel 

Replace 

Fuel vent

Fuel vent plugged 

Contaminants/residues 
in fuel 

Clean or replace 

Spark Plug 

Plug dirty/worn

Normal wear 

Clean and adjust or replace 

Carburetor Improper 

adjustment 

Vibration

Adjust 

Cooling System 

Cooling system 
dirty/plugged 

Extended operation in 
dirty/dusty locations

Clean 

Spark Arrestor 
Screen 

Spark arrestor screen 
plugged 

Normal wear 

Replace 

Engine does 
not crank 

N/A 

N/A 

Internal engine problem  See your Echo dealer 

Summary of Contents for SRM-266/S





































Reviews: