background image

B

LADE

 C

ONVERSION

 K

IT

 I

NSTALLATION

I

NSTRUCTIONS

 

P/N 99944200417

For Model: SRM-261T   S/N: ALL

X750009751

07/07

X7502233701

CONTENTS:

1, Shoulder Harness
1, Upper Plate, 20 mm
1, Lower Plate
1, Harness Clamp w/spacer
1, Harness Ring

1, Barrier Bar
1, Metal shield
1, 80-Tooth Blade
1, Bracket
3, 5mm x 15mm screws (shield mount)
2, 5mm x 8mm screws (bracket to shield)

4, 5mm nuts (Shield Assembly)
4, 5mm nuts (Barrier Bar Assembly)
4, 5mm lockwashers
1, 5 mm x 18 mm Bolt (Harness Clamp)
1, M10 x 1.25 L.H. Nut
10, Split Pins

WARNING  

  DANGER

You must install a Barrier Bar or U-Handle Kit and all Blade Conversion parts shown in the following instructions
before operating this unit with blades, otherwise serious injury may result.

IMPORTANT
If non-standard monofilament heads, METAL/PLASTIC blades or cultivators etc., are used, THE CARBURETOR
MUST BE RESET or serious engine damage can occur.  See "Carburetor Adjustment" in the unit Operator's Manual.

INSTALL

 

METAL

 

SHIELD

Tools Required: 8 x 10 mm Open-end Wrench, Screwdriver, T-wrench,

Locking Tool

Parts Required: Metal Shield, Shield Bracket,

3 - 5  x 10 mm screws w/captivated flat and lock-
washer, (metal shield to gear housing).
2 - 5 x 8 mm screws, 2 - 5 mm nuts, 2 - 5 mm lock-
washers, (bracket to shield).
2 - 5 mm nuts, 2 - 5 mm lockwashers
(bracket to gear housing)

SRM/PAS/SB BLADE SET-UP GUIDE*

 

 

 
TO USE  
THESE BLADES 

Pro Maxi-Cut 

Grass/Weed 

Plastic Cutters 

Rigid Plastic 

Tri-Cut   

Grass/Weed Blade 

Metal 

Tri-Cut/8 Tooth 

Grass/Weed Blade 

Metal 80T Brush Blade 

Metal 22T Clearing Saw Blade 

Handle 

Loop Handle, w/or 

w/o Barrier Bar 

Loop Handle 

w/Barrier Bar, 

 or U-Handle 

Loop Handle 

w/Barrier Bar, 

 or U-Handle 

U-Handle 

Debris Shield 

Metal Shield 

Metal Shield 

Metal Shield 

Metal Shield 

Harness  

 

 

Shoulder Harness

Shoulder Harness 

Shoulder Harness

Shoulder Harness****

Upper Plate & 

Flat Washer 

Upper Plate 
& Glide Cup 

Upper/Lower 

Blade Plates** 

Upper/Lower 

Blade Plates** 

Hex Nut 

Hex Nut 

Hex Nut 

Hex Nut 

 
 

You 

must 

install 

these 

parts! 

Blade 

Mounting 

Hardware 

New Cotter Pin*** 

New Cotter Pin*** 

New Cotter Pin*** 

New Cotter Pin*** 

 

 

WARNING!  DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS 

 

 

 

**  Arbor diameter of Upper Blade Plate must match arbor diameter of metal blades. 

 
 

***  New cotter pin required each time blade is installed. 

 
 

**** Brushcutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness 

Summary of Contents for SRM-261T













Reviews: