background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

17

5. Choke

After engine fires (or 5 pulls), move choke lever back to Run (

)

position.  Hold throttle trigger and throttle trigger lockout fully
depressed, and pull recoil starter starter handle/rope until engine
starts and runs. Allow engine to run at partial throttle for approxi-
mately 10 seconds. Release throttle trigger, and allow unit to warm
up at idle for several minutes.

NOTE
If engine does not start with choke in “Run” position after 5 pulls,
repeat instructions.

6. Throttle Trigger

After engine warm-up, gradually depress throttle trigger to increase
engine RPM to operating speed.

STARTING

 

WARM

 

ENGINE

The starting procedure is the same as Cold Start except DO NOT close
the choke, and do not depress throttle trigger to wide open position.

WARNING  

  DANGER

The attachment should not move at idle, otherwise serious personal
injury may result.

NOTE
If attachment moves, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO Dealer.

1. Stop Switch

Move stop switch button  (A) away from the STOP position.

2. Primer

Pump primer bulb (C) until fuel is visible and flows freely in the clear
fuel tank return line. Pump bulb an additional 4 or 5 times.

NOTE
Lightly place knee on drive shaft to stabilize unit during starting. Do
not apply excessive downward force or damage to unit can occur.

3. Recoil Starter

Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Rapidly pull recoil starter handle/rope (D) until
engine fires.

NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.

A

C

D

Summary of Contents for SRM-251U

































Reviews: