background image

17

ASSEMBLY

SRM/PAS/SB Blade Configuration

If you change the cutting attachment on your SRM, PAS,
or SB unit from nylon line head to a blade, you must also
install all of the parts required for blade operation.
These parts vary by type of blade being used, and may
include replacing the front handle with a U-Handle (See
the SRM/PAS/SB Set-Up Guide, Page 17) 

SRM/PAS/SB Blade Set-Up Guide
Use this configuration table as a guide for setting up
your unit with a blade.  See the assembly instructions in
your Operator’s Manual or Blade Conversion Kit for
specific information.

 

 DANGER

A trimmer-brushcutter unit equipped with a metal blade
can cause serious injuries if handled improperly.
ALWAYS use extreme care when carrying or handling
the unit to avoid contact with the cutting edges of the
blade.  Echo recommends using the optional plastic
blade cover to protect yourself and others from acciden-
tal blade contact.

U-handle/Blade Kit

Circular Blade Cover

SRM/PAS/SB BLADE SET-UP GUIDE*

 

 

 
TO USE  
THESE BLADES 

Pro Maxi-Cut 

Grass/Weed 

Plastic Cutters 

Rigid Plastic 

Tri-Cut   

Grass/Weed Blade 

Metal 

Tri-Cut/8 Tooth 

Grass/Weed Blade 

Metal 80T Brush Blade 

Metal 22T Clearing Saw Blade 

Handle 

Loop Handle, w/or 

w/o Barrier Bar 

Loop Handle 

w/Barrier Bar, 

 or U-Handle 

Loop Handle 

w/Barrier Bar, 

 or U-Handle 

U-Handle 

Debris Shield 

Metal Shield 

Metal Shield 

Metal Shield 

Metal Shield 

Harness  

 

 

Shoulder Harness

Shoulder Harness 

Shoulder Harness

Shoulder Harness****

Upper Plate & 

Flat Washer 

Upper Plate 
& Glide Cup 

Upper/Lower 

Blade Plates** 

Upper/Lower 

Blade Plates** 

Hex Nut 

Hex Nut 

Hex Nut 

Hex Nut 

 
 

You 

must 

install 

these 

parts! 

Blade 

Mounting 

Hardware 

New Cotter Pin*** 

New Cotter Pin*** 

New Cotter Pin*** 

New Cotter Pin*** 

 

 

*  WARNING!  DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS 

 

 

 

**  Arbor diameter of Upper Blade Plate must match arbor diameter of metal blades. 

 
 

***  New cotter pin required each time blade is installed. 

 
 

**** Brushcutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness 

Summary of Contents for SB

























































Reviews: