manualshive.com logo in svg

Echo PPF-210, Operator'S Manual, Page: 10 / 28

Share
Download
Echo PPF-210 Operator'S Manual Download Page 10

10

WARNING  

  DANGER

Saw chain is sharp! Always wear gloves when handling cutting
attachment, otherwise serious personal injury may result.

1. Loosen the (4) four lower bolts (A) on the cutting attachment, and

remove location bolt (B).

2. Slide the cutting attachment onto the shaft housing until the hole

in the neck of the cutting attachment is aligned with the hole (C) in
the housing.  (It may be necessary to rotate the saw chain slightly
to align the internal pinion and 

drive

 shaft.)

3. Insert location bolt (B) into hole (C) and tighten to snug.

4. Tighten bolts (A), clamping the cutting attachment onto the

housing.

C

ONTENTS

Due to packaging restriction the ECHO product you have purchased requires some assembly.

After opening the carton, check for damage.  Immediately notify your retailer or ECHO Dealer of damaged or missing
parts.  Use the contents list to check for missing parts.

__ Power Head/Drive Shaft Assembly
__ Cutting Attachment
__ Operator's Manual
__ Safety Manual
__ Warranty Registration Card
__ Warranty Statement
__ 1, T-Wrench (Combination screwdriver/spark plug socket)
__ 1, 4 mm Hex Wrench
__ Safety Glasses
__ Echo Power Blend 

TM

 2-stroke oil sample

__ Shoulder Harness
__ Guide Bar Cover

A

SSEMBLY

For your convenience the Power Pruner

TM

 has been shipped with the power head attached and throttle linkage assembled.

We recommend the power head remain attached to the drive shaft and housing at all times.

Tools Required: 3 mm Hex Wrench, Screwdriver, T-wrench

Parts Required: Power Head/Drive Shaft, Cutting Attachment,

3-foot Extension (Optional) P/N 99946400010

CUTTING

 

ATTACHMENT

 

TO

 

DRIVE

 

SHAFT

 

INSTALLATION

B

C

A

A

Summary of Contents for PPF-210





























Reviews:

No comments