background image

P

OWER

 P

RUNER

TM

O

PERATOR

'

S

 M

ANUAL

3

The circle with the slash symbol means whatever is
shown within the circle is prohibited.

This symbol accompanied by the words  WARNING
and DANGER calls attention to an act or condition that
can lead to serious personal injury to operator and
bystanders.

M

ANUAL

 S

AFETY

 S

YMBOLS

 

AND

 I

MPORTANT

 I

NFORMATION

Throughout this manual and on the product itself, you will find safety
alerts and helpful, informational messages preceded by symbols or key
words.  The following is an explanation of those symbols and key
words and what they mean to you.

IMPORTANT  The enclosed message
provides information necessary for the
protection of the unit.

S

AFETY

DECALS

Locate these safety decals on your unit.  Make sure the decal is legible
and that you understand and follow the instructions on it.  If a decal
cannot be read, a new one can be ordered from your ECHO dealer.  See
PARTS ORDERING instructions for specific information.

Shaft Coupler

IMPORTANT

NOTE

NOTE  This enclosed message provides
tips for use, care and maintenance of the
unit.

P/N 89016022660

Hot Decal (near muffler)

P/N 89016006361

Summary of Contents for Power Pruner PPT-260































Reviews: