manualshive.com logo in svg

Echo Power Pruner PPSR-2122, Operator'S Manual

Share
Download
Echo Power Pruner PPSR-2122 Operator'S Manual Download Page 26

26

CARBURETOR

 

ADJUSTMENT

Non Emissions Models

Tools Required:  Screwdriver with 2mm blade width, Tachometer

 (

ECHO

 P/N 99051130017)

Parts required:  None.

NOTE
If carburetor has limiter caps follow "Carburetor Adjustment"
procedures for Emission models on previous page.

Idle Speed Adjustment

Turn "idle" speed adjustment screw (C) CW (clockwise) until saw chain
begins to turn, then turn screw out CCW (counter  clockwise) until saw
chain stops turning. Turn screw out, CCW an additional 1/4 turn.

WARNING         DANGER

Saw Chain must not turn when unit is idling, otherwise serious
personal injury may result.

Basic Setting

1.

Stop engine and turn both LO (B) and HI (A) needles in, CW until
they stop and are lightly seated.

IMPORTANT
DO NOT over tighten needles. Forcing them to tighten will
damage the carburetor.

2.

Turn needles out CCW
PPSR-2122 LO (B) 1-3/8 turns; HI (A) 1-7/8 turns
PPSR-2433 LO (B) 2-1/2 turns; HI (A) 2-1/4 turns

Fine Tuning
(Requires Accurate Tachometer)

1.

Start engine and allow to warm to operating temperature (minimum
2 - 3 minutes) varying engine speed from idle to full throttle.

2.

Always begin fine tuning with LO (B) needle.
a. Lean drop-off - With engine idling, turn LO (B) needle slowly

CW (in) to lean drop-off point. RPM will increase, then
abruptly drop-off.  Note this position. (1)

b. Rich drop-off - With engine idling, slowly turn LO (B) needle

CCW (out) to rich drop-off point. RPM will increase then
gradually slow and drop-off. Note this position. (2)

c. Final setting - Set needle at mid point between lean rich drop-

off points. (3)

d. Turn needle 1/8 turn CCW (out) making mixture slightly

richer. (4)

F

A

Summary of Contents for Power Pruner PPSR-2122

































Reviews:

No comments

Brands by name

Popular brands

Load more brands