Echo Power Pruner 99944200532 Operator'S Manual Download Page 20 | Manualshive

Page: 20 / 32

background image

OPERATION

SRM-225

20

X7702092207

© 2/2017 ECHO Inc.

Adjusting Automatic Oiler

1.

From bottom of gear case, turn
adjustment screw (A) clock-
wise to decrease oil volume, or
counterclockwise to increase oil
volume.

Note: The automatic oiler is preset
to deliver a sufficient oil discharge
volume during normal operating
conditions. During heavy or dry cut-
ting conditions, the oil discharge vol-
ume may be increased to assure
adequate lubrication. If oil is leaking
from the bar cover area, reduce the
oil discharge volume. Refill the oil
reservoir with each tank of fuel.

Note: Very little visible oil on the saw chain will provide sufficient lubrication.

Pruning Techniques

Shoulder Harness (if included)

Your harness may appear different than the harness shown.

1.

Loosen the harness clamp
screw.

2.

Put the harness on and attach it
to the unit.

3.

Adjust the harness for comfort-
able operation.

4.

Tighten the harness clamp
screw.

A

A

«
...
18
19
20
21
22
...
»

Summary of Contents for Power Pruner 99944200532

































Reviews:

No comments

Related manuals for Power Pruner 99944200532

Brand: Panduit Pages: 44

Formula F732 WIZARD

Brand: Datalogic Pages: 2

Brand: paramondo Pages: 44

Brand: Omnicomm Pages: 20

Brand: omnicharge Pages: 12

Brand: Omega Pro Pages: 4

Brand: Xerox Pages: 10

Brand: Xpand Pages: 24

Brand: Yaesu Pages: 2

Brand: Baby Lock Pages: 64

Brand: RAZERTIP Pages: 32

DGIPAD-4542 - DATASHEET FOR IPAD

Brand: I.SOUND Pages: 1

SANTA FCB-XM-CH0084-120V

Brand: GE Pages: 2

ALK.00.733.15000/B

Brand: SW-Motech Pages: 14

Brand: Bogen Pages: 1

Dodge Charger TufBox

Brand: TUFLOC Pages: 6

Brand: Becker Pages: 52

Brand: Kubota Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands