manualshive.com logo in svg

Echo POWER PRUNER 99944200530, Operator'S Manual

Share
Download
Echo POWER PRUNER 99944200530 Operator'S Manual Download Page 17

P

OWER

 P

RUNER

TM

 A

TTACHMENT

O

PERATOR

'

S

 M

ANUAL

17

S

TORAGE

Storage Hook Installation

1. Insert small end of hook into locating hole on attachment shaft.

2. Slide plastic cap onto end of attachment shaft.

S

PECIFICATIONS

MODEL ----------------------------------------------------- 99944200530 POWER PRUNER

TM

 ATTACHMENT

Length ------------------------------------------------------- 1448 mm (57.0 in.)

Width -------------------------------------------------------- 102 mm (4.0 in.)

Height ------------------------------------------------------- 140 mm (5.5 in.)

Weight ------------------------------------------------------ 2.19 kg (4.84 lbs.)

Sprocket Type ---------------------------------------------- 6 tooth spur, 9.53 (3/8 in.) pitch

Drive Shaft -------------------------------------------------- 1/4 in. Flex Cable

Gear Reduction Ratio -------------------------------------- 1.5:1

Oiling System ----------------------------------------------- Automatic

Handle ------------------------------------------------------- Left foam grip

Guide Bar and Saw Chain --------------------------------- 254 mm (10 in.), 9.53 mm (3/8 in.) pitch, .050 in. gauge, 91 VX

chain.

Summary of Contents for POWER PRUNER 99944200530





















Reviews:

No comments

Brands by name

Popular brands

Load more brands