manualshive.com logo in svg

Echo PE-266S, Operator'S Manual

Share
Download
Echo PE-266S Operator'S Manual Download Page 13

PE-266/S

ASSEMBLY

X7502026302

13

© 3/2013 ECHO Inc.

ASSEMBLY

Drive Shaft/Power Head

1. Stand power head upright on a level surface.

2. Loosen the two (2) drive shaft clamp bolts (B) at engine 

drive shaft clamp, and remove center drive shaft location 
bolt (A).

3. Remove dust cap and carefully fit drive shaft assembly to 

engine making sure that inner drive shaft engages into 
clutch mount.

4. Turn drive shaft housing until locating hole lines up with 

location hole in clamp and install center drive shaft location 
bolt (A).

Note:  Gear Housing must be aligned properly with engine.  

Aligning center locating hole in driveshaft housing with center drive shaft bolt (A) provides correct 
alignment.

5. Tighten two (2) drive shaft clamp bolts (B) securely.

6. Route throttle linkage and ignition lead assembly along shaft 

and clip as shown.

Throttle Linkage and Ignition Leads

1. Close choke and remove air filter cover.

2. Place throttle linkage (C) through adjustment fixture (D) and 

install wire end into large carburetor throttle swivel hole (E). 
Check throttle for freedom of movement and that wide open 
throttle / low idle extremes are adjusted properly.  The 
throttle linkage must be adjusted by moving the adjustment 
fixture (D).  Consult with your Echo Dealer for correct 
adjustment procedure.

Parts Required:

Power Head, Drive Shaft Assembly

A

B

A

B

C

D

E

Summary of Contents for PE-266S





































Reviews:

No comments

Brands by name

Popular brands

Load more brands