background image

18

Cleaning Cylinder Fins

  1.  Remove engine cover (two screws), pull cover away from engine.  

Clean cylinder fins to allow cooling air to pass freely.

  2.  Loosely reassemble engine cover with two screws.

  3.  Tighten all screws securely.

 

exhausT

 

sysTem

Spark Arrestor Screen

Level 2.

Tools required:

    Cross Head Screwdriver, 4 mm Hex Wrench, Soft    

 

 

 

metal brush 

Parts Required: 

  Spark arrestor screen, Gasket

 

 

 

 

IMPORTANT

  

Carbon deposits in muffler will cause a drop in engine output and 

overheating.  Spark arrestor screen must be checked periodically.

  1.  Remove two engine cover screws and remove cover from engine.  

Clean cylinder fins with brush to allow cooling air to pass freely.

  2.  Remove spark arrestor cover (A), deflector (B), plate (C), gasket 

(D), and spark arrestor screen (E) from muffler.  Replace screen if 

plugged with carbon deposits.

NOTE

When cleaning carbon deposit, be careful not to damage the cata-

lytic element inside muffler.

  3.  Install spark arrestor screen, gasket, plate, deflector, and cover.

  4. 

Install engine cover or muffler cover and attach spark plug lead.

  5.  Tighten all screws securely.

a

B

D

C

E

Summary of Contents for PB-251 - 11-09





























Reviews: