background image

18

SPARK

 

PLUG

Level 2.

Tools required:

T-wrench, Feeler gauge, Soft metal brush

Parts required:

REPOWER

TM

 Tune-Up Kit P/N 90074

IMPORTANT
Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) other-
wise severe engine damage may occur.

1. Remove spark plug and check for fouling, worn and rounded center

electrode.

2. Clean the plug or replace with a new one.  DO NOT sand blast to

clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 150-170 kg/cm (130-150 in. lb.).

COOLING

 

SYSTEM

Level 2.

Tools required:

3 mm Hex wrench, 25 or 50 mm (1 or 2 in.) cleaning
brush

Parts required:

None if you are careful.

IMPORTANT
To maintain proper engine operating temperatures, cooling air
must pass freely through the cylinder fin area. This flow of air
carries combustion heat away from the engine.

Overheating and engine seizure can occur when:
• Air intakes in the crankcase are blocked, preventing cooling air from

reaching the cylinder.

• Dust and grass build up on the outside of the cylinder. This build up

insulates the engine and prevents the heat from leaving.

Removal of crankcase cooling passage blockages or cleaning of
cooling fins is considered “Normal Maintenance.” Any failure attrib-
uted to lack of maintenance is not warranted.

Summary of Contents for HC-181





























Reviews: