background image

4

WEAR HAND AND

FOOT PROTECTION

KEEP BYSTANDERS AND HELPERS

AWAY 15 M (50 FT.).

DO NOT USE

BLADES. STRING

LINE ONLY

DO NOT EXCEED

10,000 RPM.

DO NOT OPERATE

WITHOUT

GUARDS AND

SHIELDS IN

PLACE.

BEWARE

-  THROWN,

RICOCHET

OBJECTS

INTERNATIONAL

 

SYMBOLS

EQUIPMENT

Before operation a complete check of the unit must be performed;

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or

replace as needed.

• Inspect fuel lines, tank and area around carburetor for fuel leaks.

DO NOT operate unit if leaks are found.

• Inspect shield for damage and ensure that the cut-off knife issecurely

in place. Replace if either is damaged or missing.

• Check that the cutting attachment is firmly attached and in safe

operating condition.

• Check that front (loop) handle and/or optional shoulder harness are

adjusted for safe, comfortable operation. See Assembly for proper
adjustment.

• Have repairs done only by an authorized ECHO Service Dealer.

• Do not use any attachment, accessory or replacement part unless it is

recommended in the Operator's Manual.

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

HOT

SURFACE

CARBURETOR

ADJUSTMENT

- IDLE SPEED

CARBURETOR

ADJUSTMENT
- HIGH SPEED

MIXTURE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

Read and understand

Operator's Manual.

WEAR EYES, EARS

AND HEAD

PROTECTION

EMERGENCY STOP

FUEL AND OIL

MIXTURE

FINGER SEVERING

CARBURETOR

ADJUSTMENT

- LOW SPEED

MIXTURE

SAFETY/ALERT

DO NOT SMOKE

NEAR FUEL.

DO NOT ALLOW

FLAMES OR

SPARKS NEAR

FUEL.

WEAR SLIP

RESISTANT

FOOT WEAR.

Engine choke

control.

IGNITION

ON/OFF

PRIMER

BULB

Summary of Contents for GT-201





























Reviews: