Echo CS-800P Operator'S Manual Download Page 15 | Manualshive

Page: 15 / 36

background image

15

CS-800P

OPERATION

Start / Run

Ignition switch

Chain brake

Starter handle

Unlock chain brake

Choke control knob

Choke

WARNING

• After choke control knob is pulled and then

knob is returned to original position, throttle
remains a little open (latch condition).

• If engine is started in this latch condition,

chain starts to turn.
Do not start engine before chain brake is
activated.

CAUTION

• After starting the engine, immediately

squeeze and release throttle trigger for
disengaging throttle latch and returning
engine to idle, and pull front hand guard
towards the operator immediately.
(Chain brake unlocked position)

• Never use throttle latch for cutting.
• Use the chain brake only in starting or in

emergencies.

«
...
13
14
15
16
17
...
»

Summary of Contents for CS-800P





































Reviews:

No comments

Related manuals for CS-800P

Brand: Tanaka Pages: 18

Brand: Scheppach Pages: 104

Brand: Poulan Pro Pages: 15

CS-8000 TYPE1-E

Brand: Echo Pages: 34

Brand: The Handy Pages: 20

Brand: Scotts Pages: 48

Brand: Jonsered Pages: 35

Brand: Jonsered Pages: 40

Brand: Jonsered Pages: 37

Brand: Jonsered Pages: 40

Brand: Jonsered Pages: 80

Brand: Echo Pages: 72

Brand: Homelite Pages: 1

Brand: YAT Pages: 12

Brand: Garland Pages: 144

Brand: Sandri Garden Pages: 108

Brand: Makita Pages: 108

Brand: jcb Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands