manualshive.com logo in svg

Echo CS-510, Instruction Manual

Share
Download
Echo CS-510 Instruction Manual Download Page 10

8

PREPARATION FOR USE

Bar hole

Clutch cover

Adjusting screw

NOTE

Ensure that the chain is installed with the cutters
directed forward on the top of the bar.

CAUTION

•

All adjustment, should be made cold.

•

Always wear gloves when working on chain.

Proper tension

Improper tension

MOUNTING GUIDE BAR AND

CHAIN

•

Unscrew two nuts and remove clutch cover.

•

Install the spiked bumper on the front of
machine. (Use two bolts 5

×

12)

•

Mount bar and slide toward clutch to make saw
chain installation easier.

•

Install saw chain as shown.
(Ensure cutters are pointing in the right direction)

•

Install the clutch cover tighten nuts finger tight.
Ensure that chain tension adjuster fits into bar
hole.

Two bolts 5

×

12

Spiked bumper

ADJUSTMENT, CHAIN TENSION

•

Hold the bar nose up and turn the adjuster
clockwise until the chain fits snugly against the
underside of the bar.

•

Tighten both nuts with the bar nose held up.

•

Start the engine and run at low speed.
Stop and readjust if necessary.

Summary of Contents for CS-510





























Reviews:

No comments

Brands by name

Popular brands

Load more brands