Echo CS-3700ES Service Data Download Page 2

SERVICE INFORMATION

CS-3700ES
CS-4200ES

2

1  SERVICE INFORMATION

1-1 Specifications

Model

CS-3700ES

CS-4200ES

Dimensions Length*

mm(in)

383 (15.1)

Width

mm(in)

238 (9.4)

Height

mm(in)

270 (10.6)

Dry weight*

kg(lb)

4.4 (9.7)

Engine

Type

KIORITZ, air-cooled, two-stroke, single cylinder

 Ventilated piston

Rotation

Clockwise as viewed from the output end

Displacement

cm

3

(in

3

)

35.8 (2.19)

39.6 (2.42)

Bore

mm(in)

39 (1.54)

41 (1.61)

Stroke

mm(in)

30 (1.18)

30 (1.18)

Compression ratio

7.4

7.45

Carburettor Type

Diaphragm horizontal-draught with auto-return choke

Model

WT-416C

Walbro WT-594

Walbro WT-812 with primer

**

Venturi size-Throttle bore mm(in)

13.5 - 15.85  (0.532 - 0.624)

Ignition

Type

CDI (Capacitor discharge ignition) system

Spark plug

BPMR7A

RCJ6Y

Starter

Type

ES (Effortless-start)

Rope diameter x length

mm(in)

3.0 x 830 (0.12 x 32.7)

Fuel

Type

Premixed two-stroke fuel

Mixture ratio

50 : 1 (2 %)

Petrol

Minimum 89 octane petrol (RON)

Two-stroke air cooled engine oi

l

ISO-L-EGD (ISO/CD13738), JASO FC

Tank capacity

L (U.S.fl.oz.)

0.41 (13.9)

Clutch

Type

Centrifugal, 3-shoe slide with 3-tension spring

Guide bar / Saw chain lubrication type

Automatic with volume adjuster

Oil

Tank capacity

L (U.S.fl.oz.)

0.24 (8.1)

Sprocket

Type

Spur

Number of teeth

7

Pitch

in

0.325

Cutting devices

Guide bar

Type

33RD58-325

38RD58-325

43RD58-325

Called length

cm

33

38

43

Gauge

in

0.058

Saw chain

Number of drive links

56

64

72

Pitch

in

0.325

Gauge

in

0.058

* Without guide bar and saw chain.
** Primer is installed on switch bracket since serial number 36008701 on CS-3700ES.

Summary of Contents for CS-3700ES










Reviews: