Echo CS-355T-14 Operator'S Manual Download Page 32

30

CS-355T

TROUBLESHOOTING

   WARNING

Fuel vapors are extremely flammable and 
may cause fire and/or explosion. Never test 
for ignition spark by grounding spark plug 
near cylinder plug hole, otherwise serious 
personal injury may result.

Problem

Engine

— hard to start

Cause

Remedy

— 

does not start

Engine 
cranks

Fuel at  
carburetor

No fuel at  
carburetor

• Fuel filter clogged

• Clean or replace

• Fuel line clogged

• Clean

• Carburetor

• Ask your ECHO dealer

Fuel at  
cylinder

No fuel at  
cylinder

• Carburetor

• Ask your ECHO dealer

Muffler wet with 
fuel 

• Fuel mixture is too rich

• Open choke
• Clean / replace air filter
• Adjust carburetor
• Ask your ECHO dealer

Spark at end 
of plug wire

No spark at end 
of plug wire

• Ignition switch off

• Turn switch on

• Electrical problem

• Ask your ECHO dealer

Spark at plug

No spark at plug • Spark gap incorrect

• Adjust 0.65 mm (0.026 in.)

• Covered with carbon

• Clean or replace

• Fouled with fuel

• Clean or replace

• Spark plug defective

• Replace plug

Engine 
does not 
crank

• Internal engine problem • Ask your ECHO dealer

Engine 
runs

Dies or accelerates poorly

• Air filter dirty

• Clean or replace

• Fuel filter dirty

• Clean or replace

• Fuel vent blocked

• Clean

• Spark plug

• Clean and adjust / replace

• Carburetor

• Adjust

• Cooling system blocked • Clean
• Exhaust port / spark  

arrestor screen blocked

• Clean

Summary of Contents for CS-355T-14





































Reviews: