manualshive.com logo in svg

Echo CS-310, Operator'S Manual

Share
Download
Echo CS-310 Operator'S Manual Download Page 8

SAFETY

CS-310

8

X7503275401

© 02/2019 ECHO Inc.

f.

Avoid cutting above shoulder height.

g.

Follow the manufacturer’s instructions for sharpening and 
maintenance of the saw chain.

13. When boring with the chain saw, the initial cut should be introduced 

with the lower part of the nose (tip) until the hole is sufficiently large so 
as to introduce the entire nose (tip) of the guide bar. This technique 
should reduce the danger of kickback.

14. A chain saw is intended for two-handed use. Serious injury to the 

operator, helpers and/or bystanders may result from one-handed 
operation. 

a.

Allow your chain saw to cool before refueling, and do not 

smoke while refueling.

b.

Do not allow other persons or animals close to running chain 

saw or close to where a tree is being felled.

 

c.

Use extreme caution when cutting small size brush and 

saplings because slender material may catch the saw chain 

and be whipped toward you.

d.

When cutting a limb that is under tension be alert for spring-

back.

Correct Use Of Chain Brake

CHAIN BRAKE OPERATION

• Set the lever in the unlocked 

position before starting to cut.

• If the brake is tripped by kickback 

reaction, the chain will stop 
immediately. Release the throttle to 
avoid possible damage to the 
engine or clutch.

• Do not attempt to operate the engine with the brake locked.

Locked

Summary of Contents for CS-310





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands