background image

PAS A

rticulAting

 H

edge

 c

liPPer

 A

ttAcHment

O

PerAtOr

'

S

 m

AnuAl

3

 WARNING  

Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling, starting and stop-

ping instructions.

manual

 

safeTy

 

symbols

 

and

 

ImporTanT

 

InformaTIon

 

Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre

-

ceded by symbols or key words.  The following is an explanation of those symbols and key words and what they mean to 

you.

s

afeTy

InTernaTIonal

 

symbols

      CAUTION

The safety alert symbol accompanied by the word 

“CAUTION” calls attention to an act or condition 

which may lead to minor or moderate personal 

injury if not avoided.

      WARNING

The safety alert symbol accompanied by the word 

“WARNING” calls attention to an act or condi-

tion which CAN lead to serious personal injury or 

death if not avoided.

CIRCLE AND SLASh SyMBOL

This symbol means the specific action 

shown is prohibited. Ignoring these prohi-

bitions can result in serious or fatal injury.

NOTE

This enclosed message provides tips for use, care and 

maintenance of the unit.

IMPORTANT

The enclosed message provides information neces-

sary for the protection of the unit.

      DANGER

The safety alert symbol accompanied by the word 

“DANGER” calls attention to an act or condition 

which WILL lead to serious personal injury or 

death if not avoided.

Keep bystanders at least 15 

meters (50 feet) away.

AVOID KICKOUT

Beware Thrown Objects

Wear Eye Protection

Symbol 

description/application

Symbol form/shape

Symbol 

description/application

Symbol form/shape

Symbol 

description/application

Symbol form/shape

Symbol 

description/application

Symbol form/shape

Read and under-

stand  Operator's 

Manual.

Wear eyes, ears 

and head protec-

tion

Finger Severing

Safety/Alert

Plan retreat 

path  from  falling                 

objects.

Wear slip resis-

tant foot wear.

Keep feet away

from blade

Thrown

objects

Wear hand and

foot protection

DO NOT USE 

BLADES - Line 

Head Only

Rotating

Cutting Attach-

ment

Do not operate closer 

than 15 M (50 ft.) from 

electrical hazards.  

Keep bystanders 

at  least  15  meters           

(50 feet) away.    

Wear Face Shield

Keep bystanders and helpers 

away 15 meters (50 feet) away.

Summary of Contents for 99944200595





















Reviews: