background image

GT/SRM S

PLIT

 B

OOM

/PAS C

ULTIVATOR

 A

TTACHMENT

O

PERATOR

'

S

 M

ANUAL

7

C

ONTENTS

The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton,
check for damage.  Immediately notify your retailer or ECHO Dealer of damaged or missing parts.  Use the contents list to
check for missing parts.

1 - Split Boom Cultivator Attachment

- Plastic Bag (co-pack)
- Operator's Manual
- Warranty Registration Card

    -   Storage Hook Assembly

- Safety Glasses

1.

DRIVE SHAFT ASSEMBLY - Contains a specially designed liner and the flexible drive shaft.

2.

SHIELD - Attached to deflect debris away from operator and reduce accidental contact with tines.

3.

HUB - Separately attached to axle ends by clevis pin and spring pin. Tines bolt to hubs.

4.

TINES - Identical on right and left side from operator's position. See page 12 for optional settings.

5.

GREASE ACCESS BOLT - Apply lithium grease with grease gun to gear housing every 30 hours of use.

6.

GEAR HOUSING - Houses gears and ball bearings for driving tines.

7.

SERIAL NUMBER LABEL - Also serves as insertion line when drive shaft is properly engaged.

A

SSEMBLY

POWER

 

HEAD

 

SHAFT

/

LOWER

 

SHAFT

 

ASSEMBLY

Tools Required: None

Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.

1.

Set Power Head/Shaft Assembly on a level surface.

2.

Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to
lock-out position.

3.

Remove vinyl cap from attachment drive shaft.

A

B

D

Summary of Contents for 99944200500

















Reviews: