![background image](http://html1.mh-extra.com/html/ecg/edf-6013-wa/edf-6013-wa_instruction-manual_3898380059.webp)
GB
59
If one of the program indicators is on and the
button Start/Pause fl ashes:
•
The dishwasher door is open. Close it.
If the program does not start
•
Check if the power cord is plugged in the outlet
•
Check the house fuses/circuit breakers.
•
Make sure that the water supply is open.
•
Make sure that the dishwasher door is closed.
•
Make sure that you pressed the power button.
•
Check if the dishwasher fi lters and the water inlet
fi lter are not clogged.
If the indicators “Washing/Drying” and “End” are
fl ashing
•
The water overfl ow alarm is active.
•
Close the water supply and contact an authorized
service centre.
When the indicators do not turn off after the
washing process ends
•
The power button is still on.
If there is detergent residue in the detergent
dispenser
•
You poured the detergent into wet detergent
dispenser.
If water remains in the dishwasher when the
program ends
•
The drain hose is clogged or kinked.
• The
fi lters are clogged.
•
The program did not end yet.
If the dishwasher stops in the middle of the
program
• Power
outage
•
Water supply malfunction.
•
The program was switched to a pause mode.
If you can hear during the washing process the
sounds of jolts and impacts
•
Incorrectly distributed dishes.
•
The spray arms hit the dishes.
If remnants of foods remained on the dishes
•
The dishes in the dishwasher were badly arranged,
water from the spray arms did not get to all the
plates.
•
The basket is overfi lled.
•
The plates lean on each other.
•
Too small amount of the detergent.
•
Wrong washing program was selected.
•
The spray arms are clogged with food residue.
• Clogged
fi lters.
•
Incorrectly installed fi lters.
•
Clogged drain pump.
If there are white spots on the dishes
•
You used too small amo9unt of the detergent.
•
The rinse aid dispenser is set to an insuffi
cient
level.
•
Despite the high degree of water hardness the
special salt in the softener was not used.
•
The water softener is set to an insuffi
cient level.
•
The lid of the salt dispenser is not properly closed.
If the dishes are not properly dried
•
A program without drying was selected.
•
The rinse aid dispenser is set to an insuffi
cient
level.
•
You removed the dishes too early.
If there are rust stains on the dishes
•
Low quality of the stainless steel dishes.
•
High concentration of salt in the water.
•
The lid of the salt dispenser is not properly closed.
• When
fi lling the dispenser with salt contamination
of the inside of the dishwasher and dishes
occurred.
•
Poor grounding of the dishwasher.
If the problems persist even after following the
recommended measures or other defects appear,
contact an authorized service center.
WARNING
•
If there is a water leak, close the water inlet valve and contact an authorized service center. If there is on the
fl oor of the dishwasher water due to overfl ow or leak, remove it before restarting the dishwasher.
Summary of Contents for EDF 6013 WA+
