background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E32-433T20D User Manual

Copyright © 2012–20 22 , Chengdu Ebyte Electronic Technology Co., Ltd.

15

C3+C3+C3

In sleep mode (M0=1, M1=1), issue a command (HEX format) to the module serial port: C3

C3 C3,

The module returns the current configuration parameters, such as: C3 32 XX YY;

C3 is the command prefix, 32 represents the product model, XX represents the version

number, and YY represents the interface  the maximum power value of the module

(hexadecimal). The TTL interface is 0x10, RS232 is 0x40, and RS485 is 0x80

7.4 Reset command

Instruction format

Detailed description

C4+C4+C4

In sleep mode (M0=1, M1=1), send a command to the module serial port (HEX format): C4

C4 C4,

The module will generate a reset;

During the reset process, the module conducts self-check, and AUX outputs a low level.

After the reset is completed, AUX outputs a high level and the module starts to work

normally;

At this point, a mode switch can be performed or the next instruction can be initiated.

7.5 Parameter setting instructions

name

describe

Remark

0

HEAD

Fixed 0xC0 or 0xC2, indicating that this frame data is a control

command

Must be 0xC0 or C2

C0: The set parameters will be saved after

power off.

C2: The set parameters will not be saved after

power off.

1

ADDH

Module address high byte (default 00H)

00H-FFH

2

ADDL

Module address low byte (default 00H)

00H-FFH

3

SPED

7

6

Serial check digit

The serial port modes of both sides of the

communication can be different

0

0

8N1 (default)

0

1

8O1

1

0

8E1

1

1

8N1 (equivalent to 00)

5

4

3

TTL serial port rate (bps)

The baud rate of both sides of the

communication can be different. The baud rate

of the serial port has nothing to do with the

wireless transmission parameters, and does not

affect the wireless transceiver characteristics.

0

0

0

Serial port baud rate is 1200

0

0

1

Serial port baud rate is 2400

0

1

0

Serial port baud rate is 4800

0

1

1

Serial port baud rate is 9600 (default)

1

0

0

Serial port baud rate is 19200

1

0

1

Serial port baud rate is 38400

1

1

0

Serial port baud rate is 57600

1

1

1

Serial port baud rate is 115200

2

1

0

Common Wireless Air Rate (bps)

The lower the air rate, the longer the distance,

the stronger the anti-jamming performance and

the longer the transmission time.

The air wireless transmission rate of both

parties must be the same.

0

0

0

Air rate is 0.3k

0

0

1

Air rate is 1.2k

0

1

0

Air rate is 2.4k (default)

0

1

1

Air rate is 4.8k

1

0

0

Air rate is 9.6k

1

0

1

Air rate is 19.2k

1

1

0

The air rate is 19.2k (same as 101)

1

1

1

The air rate is 19.2k (same as 101)

4

CHAN

Universal model

7

6

5

keep unused

Write 0.

Summary of Contents for E32-433T20D























Reviews: