background image

Chengdu Ebyte Electronic Technology Co.,Ltd.

E31-433T17D1B User Manual

Copyright ©2012–2021

Chengdu Ebyte Electronic Technology Co.,Ltd.

13

7 Command format

In sleep mode (mode 3: M0 = 1, M1 = 1), the list of supported commands are as follows (only 9600, 8N1 format is

supported when)

No.

Command format

Description

1

C0+Working parameters

The C0+5 byte working parameter is sent in hexadecimal format, 6 bytes in all, and

must be sent continuously (power-down save)

2

C1+C1+C1

Three C1s are sent in hexadecimal format. The module returns the saved parameters

and must be sent continuously.

3

C2+Working parameters

Send C2+5 byte working parameters in hexadecimal format, 6 bytes in all, must be

sent continuously (power off without saving)

4

C3+C3+C3

Three C3s are sent in hexadecimal format. The module returns version information and

must be sent continuously.

5

C4+C4+C4

Three C4s are sent in hexadecimal format, and the module will generate a reset and

must be sent continuously.

7.1 Factory default parameter

Factory default parameter value

C0 00 00 18 50 44

Module Model

Frequency

Address

Channel

Air data rate

Baud Rate

Serial port format

Transmitting

power

E31-433T17D1B

433MHz

0x0000

0x50

1.2kbps

9600

8N1

50mW

7.2 Working parameter reading

Instruction format

Detailed description

C1+C1+C1

In sleep mode (M0=1, M1=1), a command (HEX format) is issued to the module serial port: C1

C1 C1, the module will return the current configuration parameters, such as: C0 00 00 1A 17

44.

7.3 Version number reading

Instruction format

Detailed description

C3+C3+C3

In sleep mode (M0=1, M1=1), a command (HEX format) is issued to the module serial port: C3

C3 C3, the module will return the current configuration parameters, such as: C3 32 xx yy;the

second byte represents the frequency , if it’s 32,it is the applicable frequency of 433MHz, if it’s

38, it is the applicable frequency of 470MHz, if it’s 45, it is the applicable frequency of

868MHz; If it’s 44, it is the applicable frequency of 915MHz; if it’s 46, it is the applicable

frequency of 170MHz; xx represents the version number, yy represents other features of

module.

7.4 Reset instruction

Instruction format

Detailed description

C4+C4+C4

In sleep mode (M0=1, M1=1), a command (HEX format) is issued to the module serial port::

C4 C4 C4, the module will generate a reset; during the reset process, the module performs

self-test, AUX output low level, After the completion of reset, the AUX outputs high and the

module starts to work normally. At this time, Users can switch modes or initiate the next

instruction.

Summary of Contents for E31-433T17D1B






















Reviews: