Ebyte E28-2G4M20S User Manual Download Page 10

Page: 10 / 13

Chengdu Ebyte Electronic Technology Co., Ltd.

E28-2G4M20S User

Manual

，

Chengdu Ebyte Electronic Technology Co.,Ltd.

4-9

Average ramp-up rate(Tsmax to Tp)

Average ramp-up rate

3℃/second max

Liquidous Temperature (TL)

Liquid phase temp.

183℃

217℃

Time

（

）

Maintained Above

（

）

Time below liquid phase line

60-90 sec

30-90 sec

Peak temperature

（

）

Peak temp.

220-235℃

230-250℃

Aveage ramp-down rate

（

Tp to Tsmax

）

Aveage ramp-down rate

6℃/second max

Time 25℃ to peak temperature

Time to peak temperature

for 25℃

max 6 minutes

max 8 minutes

7.2 Reflow soldering curve

8.E28 Series

Model No.

Frequency

(Hz)

Tx power

(dBm)

Distance

(km)

Package

Size

Antenna

E28-2G4T12S

SX1280

2.4G

12.5

SMD

17.5* 28.7

IPEX/PCB

E28-2G4M20S

SX1280

2.4G

SMD

15 * 26.5

IPEX/PCB

E28-2G4M12S

SX1280

2.4G

12.5

SMD

25*14

IPEX/PCB

Summary of Contents for E28-2G4M20S













Search results

Summary of Contents for E28-2G4M20S

Reviews:

Related manuals for E28-2G4M20S

Brands by name

Popular brands

Ebyte E28-2G4M20S, User Manual

Search results

Summary of Contents for E28-2G4M20S

Reviews:

Related manuals for E28-2G4M20S

Brands by name

Popular brands