Ebyte E22-900T30S1C User Manual Download Page 2 | Manualshive

Page: 2 / 27

Ebyte E22-900T30S1C User Manual Download Page 2

CONTENTS

1. OVERVIEW

........................................................................................................................................

...............................................................................................................................................................

........................................................................................................................................................................

...................................................................................................................................................................

UNCTION INTRODUCTION

...............................................................................................................................................

2. SPECIFICATION AND PARAMETER

..............................................................................................

............................................................................................................................................................

PERATING PARAMETER

...................................................................................................................................................

3 SIZE AND PIN DEFINITION

............................................................................................................

4. CONNECT TO MCU

.........................................................................................................................

5 FUNCTION DESCRIPTION

............................................................................................................

IXED TRANSMISSION

.....................................................................................................................................................

ROADCASTING TRANSMISSION

......................................................................................................................................

ROADCASTING ADDRESS

..............................................................................................................................................

.......................................................................................................................................................

...........................................................................................................................................................................

........................................................................................................................................................

5.6.1 Indication of UART output

................................................................................................................................

5.6.2 Indication of wireless transmitting

...................................................................................................................

5.6.3 Configuration procedure of module

................................................................................................................

5.6.4 Notes for AUX

....................................................................................................................................................

6 OPERATING MODE

........................................................................................................................

6.1 MODE SWITCHING

....................................................................................................................

........................................................................................................................................

............................................................................................................................................

ONFIGURATION MODE

............................................................................................................................

....................................................................................................................................

7 REGISTER READ AND WRITE CONTROL

....................................................................................

......................................................................................................................................................

«
1
2
3
4
...
»

Summary of Contents for E22-900T30S1C




























Reviews:

No comments