background image

Chengdu Ebyte Electronic Technology Co.,Ltd.

E22-400T22DC User

Manual

Copyright ©2012–2019

Chengdu Ebyte Electronic Technology Co.,Ltd.

4-17

4

LBT enable

When enabled, wireless data will be monitored

before it is transmitted, which can avoid

interference to a certain extent, but may cause

data delay.

The maximum lingering time of LBT is 2
seconds, and it will be sent when it reaches 2
seconds.

0

Disable

default

1

Enable

3

WOR transceiver control

Valid only for mode 1.
1. In the receiving mode of WOR, the module can
modify the delay time after wake-up.Default time
is 0;
2. The receiving end needs to send the command
C0 09 02 03 E8 in configuration mode (C0 is the
write command, 09 is the register initiator
address, 02 is the length, 03 E8 is the set delay,
the maximum FFFF is 65535ms, set to 0 turns off
the wake-up delay);
3. Data can be sent within the delay.

0

WOR receiver

default

The module works in WOR monitoring mode.

The monitoring period is as follows (WOR

cycle), which can save a lot of power.

1

WOR transmitter

The module receiving and transmitting

functions are turned on, and a wake-up code is

added when transmitting data.

2

1

0

WOR period

Valid only for mode 1.

Period T = (1 + WOR) * 500ms, maximum

4000ms, minimum 500ms

The longer the WOR monitoring interval period,

the lower the average power consumption, but the

greater the data delay

Both the transmitter and the receiver must be the

same (very important).

0

0

0

500ms

0

0

1

1000ms

0

1

0

1500ms

0

1

1

2000ms

1

0

0

2500ms

1

0

1

3000ms

1

1

0

3500ms

1

1

1

4000ms

07H

Write

CRYPT

_H

Key high byte (default 0

Write only, read returns 0

Used for user encryption to avoid intercepting

airborne wireless data by similar modules.

The module will internally use these two bytes as

a calculation factor to transform and encrypt the

over-the-air wireless signal.

08H

Write

CRYPT

_L

Key low byte (default 0)

80H

86H

Read

PID

Product information 7 bytes

Product information 7 bytes

7.3 Factory default parameter

No.

Factory default parameters: C0 00 00 62 00 17

Model No.

Frequency

Address

Channel

Air data rate

Baud rate

Serial format

Power

E22-400T22DC

433.125MHz

0x0000

0x17

2.4kbps

9600

8N1

22dbm

Summary of Contents for E22-400T22DC

























Reviews: