Ebyte E22-230T30D User Manual Download Page 2

Page: 2 / 27

Chengdu Ebyte Electronic Technology Co.,Ltd.

E22-230T30D User Manual

，

Chengdu Ebyte Electronic Technology Co.,Ltd.

Disclaimer.............................................................................................................................................................3
1 Introduction........................................................................................................................................................4

1.1 Brief Introduction........................................................................................................................................4
1.2 Features.......................................................................................................................................................4
1.3 Application Scenarios................................................................................................................................. 5

2 Specifications.....................................................................................................................................................5

2.1 Limit Parameters.........................................................................................................................................5
2.2 Working Parameters....................................................................................................................................5

3 Mechanical Dimensions and Pin Definitions.....................................................................................................7
4

Recommended Connecting Diagram

................................................................................................................8

Function Details

............................................................................................................................................9

5.1

Fixed Point Launch................................................................................................................................9

5.2

Broadcast Transmission.........................................................................................................................9

5.3

Broadcast Address............................................................................................................................... 10

5.4

Listening Address................................................................................................................................10

5.5

Module Reset.......................................................................................................................................10

5.6

AUX Explained................................................................................................................................... 10

6 Working mode................................................................................................................................................. 12

6.1

Mode Switching...................................................................................................................................13

6.2

General Mode (Mode 0)...................................................................................................................... 13

6.3

WOR Mode (Mode 1)..........................................................................................................................14

6.4

Configuration Mode (Mode 2)............................................................................................................ 14

6.5

Deep Sleep Mode (Mode 3).................................................................................................................14

7 Register Read/Write Control............................................................................................................................15

7.1

Command Format................................................................................................................................15

Summary of Contents for E22-230T30D




























Search results

Summary of Contents for E22-230T30D

Reviews:

Related manuals for E22-230T30D

Brands by name

Popular brands

Ebyte E22-230T30D, User Manual

Search results

Summary of Contents for E22-230T30D

Reviews:

Related manuals for E22-230T30D

Brands by name

Popular brands